Related Manuals for Beninca HEADY 24
Summary of Contents for Beninca HEADY 24
- Page 1 L8542221 07/2012 rev 2 HEADY 24 UNIONE NAZIONALE COSTRUTTORI AUTOMATISMI PER CANCELLI, PORTE SERRANDE ED AFFINI...
- Page 2 HEADY Rimuovere le 4 viti A , quindi rimuovere il coperchio B Enlever les 4 vis A puis enlever le couvercle B Sul fondo del contenitore centrale sono presenti 4 predisposi- Au fond du boîtier de la centrale se trouvent 4 ouvertures spé- zioni (C) da rompere con un cacciavite.
- Page 3 F1 (230V): 1.6 AT F1 (115V): 3.15 AT 24Vac Code _ _ _ _ 1 2 3 4 5 6 9 10 11 12 13 14 15 16 17 18 19 20 23 24 25 26 Photo Test LAMP 24Vdc SERL...
-
Page 4: Encoder Wiring
1 2 3 4 5 6 9 10 11 12 13 14 15 16 17 18 19 21 23 24 25 26 Collegamento ENCODER ENCODER WIRING + s - + s - 3+3 x 0.5mm max 10m test1:on test2:ON 24Vac PHOTO 24Vac PHOT-C... - Page 5 Via Capitello, 45 - 36066 Sandrigo (VI) - Italy Declares that the product: Command central for 1 24Vdc motor, for single or sliding doors: HEADY 24 is compliant with the conditions of the following EC Directives: • DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of December 15 2004 regarding...
-
Page 6: Technical Data
433,92 MHz confgurabile (rolling-code or programmable + rolling-code) Rolling code transmitters supported 64 HEADY 24 CONTROL UNIT AUTOSET FUNCTION IMPORTANT: The control unit is equipped with the Autoset function to automatically set the main functioning values based on the type of installation. -
Page 7: Parameters (Par)
Extractable Eprom Memory. Contains all the control unit configurations (logics, parameters, C O N F IG UR A T I O N etc.), including the radiotransmitters. In case of faults it is possible to extract Eprom and MEMORY insert it into a different control unit, avoiding reprogramming. ENCODER WIRING In case the motor is with Encoder and one wished to connect it to the control unit, carry out the connections indicated in Fig.2, in this case the SWO1 and SWO2 inputs may not be used as Limit switch inputs. - Page 8 The anti-crash device* (amperometric sensor) operation is adjusted in the open- PMo2 1-99-(50%)** ing phase, at normal speed - Motor 2. The anti-crash device* (amperometric sensor) operation is adjusted in the closing PMc2 1-99-(50%)** phase, at normal speed - Motor 2. Mot.2 opening delay time.
- Page 9 Select the 1/2 motors operating mode: 1mot On: Only motor 1 operating. (OFF) Off: Both motors operating. The code programmable transmitters is enabled or disabled. On: Radio receiver enabled only for rolling-code transmitters. Cvar (OFF) Off: Receiver enabled for rolling-code and programmable code transmitters (self-learning and Dip Switch).
- Page 10 By selecting this function, the receiver goes into waiting (Push) for a transmitter code to erase from the memory. If the code is valid, it is erased and the message OK is displayed If the code is not valid or not present in memory, the message Err is displayed Completely erases memory of the receiver.
-
Page 11: Error Messages
TRANSMITTERS REMOTE LEARNING If an already memorised transmitter is available in the receiver it is possible to carry out remote radio learning (without needing to access the control unit). IMPORTANT: The procedure must be carried out with leaves in opening during TCA pause or with an open gate if the TCA logic is OFF.
Need help?
Do you have a question about the HEADY 24 and is the answer not in the manual?
Questions and answers