Advertisement
Quick Links
APPLICATION
The STAR1000EVO is a high capacity single channel commercial access
control receiver for commercial door openers, and dry contact triggered
devices. The STAR1000EVO is compatible with Security 2.0™ remote
controls and wireless keyless entries. The receiver capacity is 1,000
devices and can be any combination of remote controls and wireless
keyless entries. The receiver is watertight according to IPX44
specification.
INSTALLATION
. 1
S
e
e l
t c
a
o c
n
e v
i n
n e
l t
c o
t a
o i
n
receiver within "line of sight" of the intended transmitting location.
N
O
T
E:
Do not mount LCD screen in direct sunlight. Avoid mounting
the receiver in a metal enclosure or near other wireless receiving or
transmitting devices.
. 2
M
o
u
t n
h t
e
b
a r
k c
t e
o t
h t
e
d
s e
(not provided) (Figure 1).
. 3
R
e
m
o
e v
h t
e
4
# (
) 8
c s
e r
w
s
faceplate. Unplug the keypad connector from the control board.
N
O
T
: E
Be careful not to damage the keypad cable while removing the
faceplate.
. 4
M
a
e k
w
r i
n i
g
o c
n
n
e
t c
o i
s n
F (
door opener owner's manual for more specific information.
5. Reconnect the keypad connector to the board (labeled J9).
6. Secure the faceplate with the 4 (#8) screws previously removed.
7. Install the antenna provided.
N
O
T
: E
Use the optional ANT4X-1LM antenna extension kit
(see page 4) to mount the remote antenna as high and far from
metallic objects as possible for best radio range.
. 8
S
n
p a
h t
e
e r
e c
v i
r e
o
n
o t
h t
e
(#8) screws provided.
9. Tighten the watertight connector to secure and seal the wiring.
Figure 1
Antenna
Connector
Backup Memory
Module
+
n
e
r a
h t
e
o
p
ener to be controlled by the
r i
d e
s
r u
a f
e c
i w
h t
p a
p
o r
r p
a i
e t
o
n
h t
e
b
a
k c
f o
h t
e
e r
e c
v i
r e
n a
g i
u
e r
2
. )
R
f e
r e
o t
o y
r u
g
a
e t
r o
m
o
u
t n
n i
g
b
a r
k c
t e
n a
d
e s
u c
e r
Mounting Bracket
Watertight Connector
Keypad Connector
COMMERCIAL ACCESS CONTROL RECEIVER
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving residential gate,
residential garage door or a commercial door:
•
A
L
W
A
Y
permit children to operate, or play with remote control transmitters.
•
A
i t c
a v
e t
adjusted, and there are no obstructions to door travel.
•
ALWAYS keep residential gate, residential garage door or commercial door in
sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
h
a
d r
w
a
e r
To prevent possible SERIOUS INJURY or DEATH, the use of
d
e r
m
o
e v
h t
e
CONSTANT OPERATION on residential openers is PROHIBITED.
When a receiver is used to activate a commercial door opener, a
reversing edge MUST be installed on the bottom of the door. Failure to
install a reversing edge under these circumstances may result in
SERIOUS INJURY or DEATH to persons trapped beneath the door.
o c
m
m
e
c r
l a i
i w
h t
h t
e 2
Figure 2
9 - 30 volts AC/DC
250 mA max
Power
Supply
(not provided)
1
MODEL STAR1000EVO
S
e k
p e
e r
m
o
e t
o c
t n
o r
s l
u o
o t
r f
a g
e t
r o
o d
r o
O
N
L
Y
w
e h
i n
c t
n a
Connection
Connection
Single Operator
a e
h c
f o
h c
d l i
e r
. n
N
E
V
E
R
y l r
e b
e s
n e
c
e l
r a
, y l
s i
p
o r
e p
Relay
Power
Receiver Without
Faceplate
Control
Station
Advertisement
Related Manuals for Merlin GRIFCO STAR1000EVO
Summary of Contents for Merlin GRIFCO STAR1000EVO
- Page 1 COMMERCIAL ACCESS CONTROL RECEIVER MODEL STAR1000EVO APPLICATION The STAR1000EVO is a high capacity single channel commercial access control receiver for commercial door openers, and dry contact triggered To prevent possible SERIOUS INJURY or DEATH from electrocution: devices. The STAR1000EVO is compatible with Security 2.0™ remote •...
- Page 2 Merlin GRIFCO logo is displayed. Select “UNLOCK” and enter ® ® up, the system firmware revision is displayed for 5 seconds followed PIN to continue. by the Merlin GRIFCO logo. When a key is pressed, “CREATE PIN?” ® ® is displayed.
- Page 3 Displays a range of suspended locations starting from a specified location. SETTINGS Change or Delete the 6-digit PIN number for the receiver. SERVICE INFO Displays Merlin/Grifco 10-digit contact phone number. FIRMWARE VERSION Displays the current firmware version. BEEP Turn the audible feedback on or off.
- Page 4 Remote Control s............E945M, E950M, E943M, E940M, E960M (Merlin) &...
Need help?
Do you have a question about the GRIFCO STAR1000EVO and is the answer not in the manual?
Questions and answers