Related Manuals for peerless-AV PeerSound ADS100-B
Summary of Contents for peerless-AV PeerSound ADS100-B
- Page 1 User Manual and Installation Guide Wireless Audio System Models: ADS100-B ISSUED: 08-30-13 SHEET #: 180-9051-1...
-
Page 2: Table Of Contents
Contents Important Safety Instructions ......................3 Important Information ........................4 Unit Care Recommendations ......................4 Specifi cations ..........................5 Introduction ............................6 What’s In The ADS100-B Box ......................6 Tools Needed For Installation ......................6 Installation Planning ........................6 Installation ............................7 Product Overview .......................... -
Page 3: Important Safety Instructions
Important Safety Instructions Warnings/Safety 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions. 8. -
Page 4: Important Information
17. Avoid overloading electrical outlets or extension cords which otherwise could result in electric shock or fi re. 18. To avoid electric shock, never stick anything in the slots on the case or remove the cover. 19. This product is intended for indoor use only. 20. -
Page 5: Specifi Cations
SPECIFICATIONS T8 Transmitter • Size: 17 ¼”w x 1 11/32” h x 7”d • Rack Height: • Power Input: 120/240 VAC 50/60Hz to supplied AC adapter (5VDC @ 1000 mW) • Line Level Inputs: Qty 8 independent RCA • Speaker Level Inputs: Qty 8 independent, 150 watts max each, 2 pole plug •... -
Page 6: Introduction
Introduction The Peer Sound Wireless Audio System provides for eight total independent channels, four total stereo zones or any combination in-between. By connecting your source(s) to either the RCA line level or speaker level inputs, you can wirelessly transmit the audio signal and amplify it for the remote speakers. -
Page 7: Installation
Installation Product Overview Front 1. POWER • Turns unit ON/OFF 2. SYNC 1-4 • Used to pair amps for channels 1-4 3. SYNC 5-8 • Used to pair amps for channels 5-8 Back 1. Transmitter Module • Sends signal to RX on amp 2. - Page 8 Installation Product Overview Front 1. RX MODULE • Insert RXS or RXM Module here 2. POWER INDICATOR • Blue when power is on. Back 1. Power Connector 2. Ground Connector 3. Speaker Connector ISSUED: 08-30-13 SHEET #: 180-9051-1 8 of 16...
-
Page 9: Transmitter: Mounting
Installation Transmitter Mounting If the transmitter will not be installed in an AV rack, then leave the rubber feet in place. If the transmitter will be installed in an av rack, then remove the four rubber feet from the base. Step 1 Use the supplied M3 screws to install the rack ears onto the chassis. -
Page 10: Transmitter: Tx Module Connections
Note: For best transmission the antenna should be positioned straight or at a 90° angle once screwed onto the bulkhead connector. Not turned 180° facing the cable. TX Module Connections Step 1 Insert the ADS100-TX14 module into the rear connector labeled “Transmit 1-4”. Be sure alignment pin goes into matching hole. -
Page 11: In-Wall Installation Of The Ads100-A252 Wireless Receiver/Amplifi Er
Amplifi er/Receiver In-Wall Installation of the ADS100-A252 Wireless Receiver/Amplifi er The installation shall be carried out in accordance with all applicable installation rules. Step 1 Locate area that In-Wall amp will be installed. Step 2 To verify mounting placement of amplifi er/speaker, conduct a stud search to determine stud layout. For In-Wall Amplifi... -
Page 12: Transmitter And Amplifi Er Pairing
Step 7 Connect speaker wires to the speaker terminal plug. Strip 3/16” insulation off the speaker wires, loosen the screw clamp, insert the wire, and tighten screw clamp. Be sure to follow the positive and negative nomenclature. Step 8 Take the ADS100-RXS stereo RX module and plug into the port on the amplifi er. Install the M3 phillips locking screw through the RX module into the amplifi... -
Page 13: Stereo Vs Mono Setup
Finalizing The Installation Step 1 Feed the amplifi er though the wall cut-out by holding the oval cutouts located on the bracket. Guide the amp in and down toward the wiring fi rst, then back up so the top of the holding bracket is just outside of the wall. -
Page 14: Faqs
FAQs I plug my CD player in and I get maximum volume with no level control. How is level controlled? A. ADS100-B is a replacement for wires and has no inherent level control. Level needs to be controlled from the source device such as an iPod when using the line level inputs or the amplifi er volume when using the speaker level inputs. -
Page 15: Limited Warranty
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless-AV®, (b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless-AV®’s instructions or warnings when installing, using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third-party actions and force majeure. - Page 16 Peerless -AV 2300 White Oak Circle Aurora, IL 60502 USA peerair.peerless-av.com ©2013 Peerless-AV. All rights reserved. Peerless-AV is a trademark of Peerless Industries, Inc. Other parties’ marks are the property of their respective owners.