Table of Contents
Advertisement
Quick Links
EA08
HYDRAULIC
EARTH AUGER
WARNING
S
, O
M
AFETY
PERATION AND
AINTENANCE
USER'S MANUAL
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie OR 97267-5698
Copyright
©
The Stanley Works 2005
503-659-5660
OPS/MAINT USA
FAX 503-652-1780
Printed in U.S.A.
www.stanley-hydraulic-tools.com
43668 9/2005 ver 3
Advertisement
Table of Contents
Related Manuals for Stanley EA08
Summary of Contents for Stanley EA08
- Page 1 EA08 HYDRAULIC EARTH AUGER WARNING AFETY PERATION AND AINTENANCE USER'S MANUAL Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie OR 97267-5698 Copyright © The Stanley Works 2005 503-659-5660 OPS/MAINT USA FAX 503-652-1780 Printed in U.S.A. www.stanley-hydraulic-tools.com 43668 9/2005 ver 3...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certifi ed dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. - Page 4 Self EN ISO 3744 1994 Self Machinery directive 98/37/EC 1998 Self Special Provisions: None Spezielle Bestimmungen: Dispositions particulières: Provisiones especiales: Disposizioni speciali: Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA Date/Datum/le/Fecha/Data 6/28/01 Signature/Unterschrift/Signature/Firma/Firma__________________________________________________________________________ Position/Position/Fonction/Puesto/Posizione Engineering Manager 8/1/05...
-
Page 5: Safety Symbols
SAFETY SYMBOLS Safety symbols and signal words, as shown below, are used to emphasize all operator, maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. -
Page 6: Safety Precautions
If so, place the added precautions in the space provided on page 5. The EA08 Hydraulic Earth Auger will provide safe and dependable service if operated in accordance with the instructions given in this manual. Read and understand this manual and any stickers and tags attached to the tool and hoses before operation. - Page 7 • Do not exceed the rated limits of the tool or use the tool for applications beyond its design capacity. • Always keep critical tool markings, such as lables and warning stickers legible. • Always replace parts with replacement parts recommended by Stanley Hydraulic Tools. • Check fastener tightness often and before each use daily.
-
Page 8: Tool Stickers & Tags
USE ONLY PARTS AND REPAIR USE ONLY PARTS AND REPAIR PROCEDURES APPROVED BY PROCEDURES APPROVED BY and understand the safety STANLEY AND DESCRIBED IN THE OPERA- STANLEY AND DESCRIBED IN THE OPERA- TION MANUAL. TION MANUAL. instructions listed on this... -
Page 9: Hydraulic Hose Requirements
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydrau- lic Tools. DO NOT REMOVE THESE TAGS. -
Page 10: Htma Requirements
HTMA REQUIREMENTS TOOL CATEGORY HYDRAULIC SYSTEM REQUIREMENTS TYPE 1 TYPEII TYPEIII TYPE RR FLOW RATE 4-6 gpm 7-9 gpm 11-13 gpm 9-10.5 gpm (15-23 lpm) (26-34 lpm) (42-49 lpm) (34-40 lpm) TOOL OPERATING PRESSURE 2000 psi 2000 psi 2000 psi 2000 psi (at the power supply outlet) (138 bar) -
Page 11: Operation
1. The torque tube is attached to the base as shown in fi g- INSTALL AUGER BIT ure 3. Be sure to use the cotterless clevis pin provided with the unit. Make sure the pin is pushed through both holes in The EA08 Earth Auger accepts standard 1-1/4 inch square the base. -
Page 12: Connect Hoses
6. Lower the EA08 until the auger starts digging. With soft soil the auger will penetrate into the ground with little effort and may require you to apply a slight lift to the EA08. With hard soil the auger cannot penetrate the ground easily and Figure 3. -
Page 13: Troubleshooting
TROUBLESHOOTING If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the tool, always check that the hydraulic power source is supplying the correct hydraulic fl ow and pressure to the tool as listed in the table. Use a fl owmeter known to be accurate. Check the fl ow with the hydraulic oil temperature at least 80°F/27°C. -
Page 14: Specifications
SPECIFICATIONS Pressure Range ............................2000 psi/140 bar Maximum Back Pressure ..........................250 psi/17 bar Couplers ....................HTMA/EHTMA Flush Face Type Male & Female Connect Size and Type ......................... 1/2 in. Male Pipe Adapter Weight ................................47 lbs / 21 kg Overall Length ............................... 41 in. / 104 cm Overall Width .............................. -
Page 15: Ea08 Parts Illustration
EA08 PARTS ILLUSTRATION... -
Page 16: Ea08 Parts List
EA08 PARTS LIST Item Part No. Description 37919 Handle 39415 Capscrew 39276 Motor (Parker TB-0165-F-S-10-0-AAAB 37917 Base Assy 06151 Capscrew ----- Clevis Pin (furnished with item 28) 00720 Set Screw ----- Key (furnished with item 3) 11207 Circuit Type D Sticker... -
Page 17: Warranty
fi rst retail purchaser, or for a period of 2 years from the shipping date from Stanley, whichever period expires fi rst, to be free of defects in material and/or workmanship at the time of delivery, and will, at its option, repair or replace any tool or part of a tool, or new part, which is found upon examination by a Stanley authorized service outlet or by Stanley’s factory in Milwaukie, Oregon to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. - Page 18 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www.stanley-hydraulic-tools.com...