Page 2
Introduction Thank you for choosing Logika. Please take a moment to carefully read through the manual to ensure safe and proper installation and use. • Before use, the product must be properly installed as described in this manual by a qualified technician.
Packing List Item Name Quantity Front Plate Back Plate Lock Body Accessories Package User Manual Hole Drilling Template Pencil Warranty Card Magnetic Card (not included in non-NFC version) Door Frame Box Strike Plate...
Features • Communication Mode: IEEE 802.15.4 Zigbee. Supports multiple unlocking methods: Smart phone, pin code and fingerprint identification • (and NFC in selected versions). Supports linkage control: Allowing scenes to be set up to cater for different needs. • Monitors access and reports to mobile app. •...
Preparation Before Installation Prior to installing the door lock, you need to determine the opening direction of the door, as there are some adjustments that may need to be made to the lock body, door handle orientation and the spindle rotation direction. Don’t worry if you get it wrong, as it’s easy enough to remove the lock from the door and re-adjust, if necessary.
Page 8
Lock Body Adjustment Having determined the door opening direction, we first need to adjust the direction of the door latch on the lock body, so that it will engage correctly when the door closes. The rule of thumb here is quite simple. Simply rotate the door latch so that its bevel (curved bit) points in the direction of the door frame, once it is fitted into the door.
Page 9
Door Handle Orientation Depending on the door opening direction, you may need to rotate the handles on the front and rear plates of the door unit. The procedure below explains how to do this. 1) Using a Philips screwdriver, remove the screw holding the handle in place, as shown.
Page 10
Adjust Spindle Clutch Finally, we need to adjust the spindle clutch on the Front Panel, according to the door opening direction. Marked on this clutch are the letters L (for Left) and R (for Right). These letters correspond with a Left Inward/Outward opening door and a Right Inward/Outward opening door respectively.
Page 11
Installing the Door Lock Installing the Lock Body 1) Measure the point where you wish to place the lock template – Typically, 1000mm to 1200mm from the bottom and 60mm from the edge of the door. 2) Mark this point. 3) Place the supplied template to line up the marker with the reference mark on the template.
Page 12
7) Insert the Lock Body and make sure all the holes line up. 8) Screw the Lock Body in place. It’s now ready for the attachment of the front and rear door lock plates.
Installing the Front Plate 1) Install the two connecting bolts. 2) Connect the cable interconnect and Large square spindle. 3) Affix the front plate to the door. 4) Turn the handle to make sure the door latch works as expected.
Installing the Back Plate 1) Attach the small square spindle. 2) Connect the cable interconnect to the connector on the back plate. 3) Affix the back plate to the door, making 4) Screw the back plate in place and insert the batteries.
Page 15
Adding the Device to the Smart Home Network Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the Logika Smart Mobile App user guide which will take you through the process of adding smart devices to the system.
User Administration and Security Entering Admin Mode 1) Tap the touchpad screen to wake it up. 2) Tap the * key twice in quick succession. 3) Enter the admin code (Default is 123456) followed by the # key. 4) The display will now show you some admin options that you can use. Note: Don’t forget to change the Admin passcode from the default for complete security! Set Time Once the door lock is connected to the Smart Home system (as described previously), the time will...
Add New User 1) Select Add User. 2) Select the type of user you wish to add. 3) Enter a username (up to 5 characters). 4) Type the passcode (6 digits) and/or start fingerprint recognition and/or NFC programming. Note: The NFC function is only available on some models. Delete User Note: Delete All deletes all data relating to that user –...
Page 18
Set Always-Open (Unlocked) Mode This setting disables the security on the door lock, so that anyone can gain access without having to type a passcode, use fingerprint identification or NFC card. To disable this, after it’s been set, simply enter your passcode, fingerprint or NFC card. Enable Double Authentication This can be enabled to force each user to use two methods of authentication before they gain access.
Scene. For instance, you could engage the security cameras, turn off all the lights and heating, etc when you leave the house. Refer to the Logika Smart Mobile App user guide for information on how to set up a Scene. Leave Home Button...
The issue you are experiencing is not mentioned here. Micro-USB Socket Please contact us at support@logika.nz with your issue and we will do our utmost to help!