Seiko S149 Instruction page 8

Printout after the measurement
POWER
ON
（１）Turn on the power switch.
（２）Press memory recall
button (RECALL).
SYSTEM STOPWATCH
The time data stored in
300LAP／SPLIT MEMORY
SPLIT
memory are printed out.
F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
STOP-W. A/S SET TIME
＊When all the stored data are
LOCK
CLEAR printed out, the printer
LAP／SPLIT START
automatically stops.
RESET STOP
1/100 STOP.W A/S SET TIME
RECALL
・The stored data can be printed out as many
times as necessary.
・Printout can be selected from only the desired
block of data and all the blocks of data.
"To print out the data in all the blocks in memory"
①Turn on the power switch of the printer.
②Show the memory recall display, and keep recall button
③Printout of all the blocks of data
・Keep recall button pressed further until "Print All" is displayed.
④Then, release recall button. The data in all the blocks is displayed
quickly one after another starting from Block "1", and will be
printed out at a stretch.
(While the data is displayed quickly one after another, the
stopwatch checks for the fastest lap time in each block.)
Notes:
＊While the printout is under way, none of the stopwatch buttons will work.
・Once started, the printout cannot be canceled halfway.
・Even if the power switch of the printer is turned off while the printout is in progress, the button operation of the stopwatch is nullified until entire
data to be printed is shown on the display.
Printout of lapse of time
・In addition to the elapsed time, the stopwatch can print out the
time when the lap time is measured.
・The time a lap time is measured is not stored in memory.
□ １ Turn on the power switch for printer and then press
selection button②(TIME)
time/calendar mode.
POWER
ON
（１）Turn on the power switch.
（２）Press mode selection button ③
(TIME) to set the stopwatch to
the time/calendar mode.
SYSTEM STOPWATCH
300LAP／SPLIT MEMORY
SPLIT
F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
STOP-W. A/S SET TIME
LOCK
CLEAR
LAP／SPLIT START
RESET STOP
1/100 STOP.W A/S SET TIME
RECALL
"Printout of the desired block of data"
① Memory recall
Show the memory recall display, and
select the block of data you wish to
print out.
・If recall button is released immediately after flashing "Print" is displayed, the printout
will be canceled and the display returns to the memory recall display.
④ Keep recall button pressed for 1 second, and then release it as "Print" stops flashing and remains displayed.
The data in the selected block is displayed quickly one after another, and then printout is started.
(While the data in the block is displayed quickly one after another, the
stopwatch checks for the fastest lap time in the selected block.)
pressed. Flashing "Print" is displayed.
mode
to set the stopwatch to the
SPLIT
F
Block No. for the block of data to be printed
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
(Start data)
Recall button
(Printout display for desired block of data)
STOP
BATT .
LAP
RECALL
The total elapsed time of the block is displayed.
SPLIT
BLOCK
LAP
STOP
BATT .
LAP
RECALL
(Printout of all the blocks of data)
Recall button
＊Please note that the time of measurement cannot be printed out
unless the stopwatch is reset to "00".
Stopwatch
mode
SPLIT
F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
②Turn on the power switch of the printer.
③Keep recall button pressed.
When the stopwatch confirms the
"Power on" of the printer, flashing
"Print" is displayed.
SPLIT
F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL
Recall button
F
E
F
E
Time/calendar
mode
ID
F
BLOCK
LAP
STOP
BATT .
LAP
E
RECALL