Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for AEG Powertools ACS18BS6
- Page 2 mportant! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modifications.
- Page 3 ACS18BS6...
- Page 4 ACS18B...
- Page 5 FRONT HAND GUARD/ CHAIN BRAKE CHAIN COVER FRONT HANDLE BAR MOUNTING NUTS TRIGGER RELEASE THROTTLE TRIGGER REAR HANDLE CHAIN CHAIN TENSIONING CATCHER SCREW SAW CHAIN METAL LOOP BATTERY COMBINATION WRENCH CHAIN LUBRICANT SPIKED BUMPER GUIDE BAR GUIDE BAR COVER...
- Page 7 START STOP...
- Page 9 APPROX. 4-5.5 mm FLATS click...
- Page 11 click...
- Page 12 click...
- Page 13 START STOP...
- Page 14 BRAKE ON BRAKE OFF...
- Page 16 CHAIN DRIVE LINKS GROOVE...
- Page 17 APPROX. 4-5.5 mm FLATS...
- Page 18 click...
- Page 24 Figure 1 Figure 6 Figure 2 Figure 7 Figure 3 Figure 8 5 cm / 2 in 5 cm / 2 in Figure 4 Figure 9 Figure 5 Figure 10...
- Page 25 Figure 11 Figure 12 Figure 13 Figure 14...
- Page 26 TECHNICAL DATA CORDLESS CHAINSAW ACS18BS6 ACS18B Rated voltage 18 V 18 V Max bar length 300 mm (12”) 300 mm (12”) Chain oil tank capacity 210 ml 210 ml Weight (without battery pack, with guide bar, chain and empty tank) 3.3 kg...
- Page 27 PERSONAL SAFETY packs. Use of any other battery packs may create a risk of injury and fire Stay alert, watch what you are doing and use common sense When battery pack is not in use, keep it away from other metal when operating a power tool.
- Page 28 handle and your left hand on the front handle. Holding the Only use replacement bars and chains specified by the to d chainsaw with a reversed hand configuration increases the risk of manufacturer. Incorrect replacement bars and chains may cause personal injury and should never be done.
- Page 29 to do so could result in possible serious personal injury. Remove dirt, stones, loose bark, nails, staples, and wire from the tree. Do not stop the saw in the middle of a cutting operation. Keep the Do not attempt to fell trees which are rotten or have been damaged saw running until it is already removed from the cut.
- Page 30 Limbing a tree KNOW YOUR PRODUCT See figures 12 - 13. See page 5. Limbing is removing the branches from a fallen tree. When limbing, Front hand guard/Chain brake leave larger lower limbs to support the log off the ground. Remove this Front handle the small limbs in one cut.
- Page 31 OPERATION handle. Allow the back of your hand to push the chain brake lever/ hand guard toward the bar while the chain is rotating rapidly. Be sure to maintain both hands on the saw handles at all times. WARNING! If any parts are damaged or missing do not operate the product until the parts are replaced.
- Page 32 Put the new chain in the correct direction onto the bar and make sure that the drive links are aligned in the bar groove. Do not expose to rain or damp condition. Attach the bar to the chain saw and loop the chain around the drive sprocket.
- Page 33 ally lain ded, ded, ded,...
- Page 36 Techtronic Industries GmbH Techtronic Industries (Australia) Pty. Ltd. Techtronic Industries New Zealand Ltd. Max-Eyth-Straße 10 31 Gilby Road, 2 Landing Drive, Auckland Airport, Mangere, New Zealand 2022 71364 Winnenden Mount Waverley VIC 3149, Germany Australia 960087163-01...
Need help?
Do you have a question about the ACS18BS6 and is the answer not in the manual?
Questions and answers