Related Manuals for Kathrein UFD 400
Summary of Contents for Kathrein UFD 400
- Page 1 All manuals and user guides at all-guides.com Operating manual Kathrein Satellite Receiver UFD 400 Order No.: 260 467...
-
Page 2: Table Of Contents
All manuals and user guides at all-guides.com Contents Inhalt Controls, displays and connections................3 View of front panel, rear panel and remote control handset............... 3 Description of controls, displays and connections ..................4 Safety instructions......................5 Important notes regarding operation ......................5 Important notes on siting and installation .................... -
Page 3: Controls, Displays And Connections
All manuals and user guides at all-guides.com Controls, displays and connections Bedienelemente, Anzeigen und Anschlüsse This section contains a brief description of all the control elements, displays and connections. The key symbols presented here are also used when describing the operating sequences. -
Page 4: Description Of Controls, Displays And Connections
All manuals and user guides at all-guides.com Controls, displays and connections Front panel controls and displays Rear panel controls and connections Mains switch (with mains isolation) Mains input socket for 230 V/50 Hz Buttons for programme selection DATA socket Step-by-step programme selection (upwards and down- a) Connection facility for the URS 200 external infrared wards). -
Page 5: Safety Instructions
All manuals and user guides at all-guides.com Safety instructions Sicherheitshinweise The following section contains important information relating to operation, place of installation and connecting-up of the receiver. Read these notes carefully before putting the unit into operation. Important notes regarding operation Extended absence / Thunderstorms Always switch the unit off via its mains switch during periods of extended absence or at the onset of thunderstorms. -
Page 6: Important Notes On Siting And Installation
If the feeder system (LNB) is supplied with an external supply voltage and the LNB supply voltage is not used for polarity switchover (e.g. Kathrein single-cable feeder system UAS 330), the receiver‘s LNB supply must be set to “OFF“ (refer to section: “Initial settings, LNB supply voltage“). -
Page 7: Connecting Up And Putting Into Operation
All manuals and user guides at all-guides.com Connecting up and putting into operation Anschluß und Inbetriebnahme The following section is intended specifically for the specialist dealer. If you are not carrying out the installation yourself, there is no need to pay any attention to this section. -
Page 8: Inserting Batteries Into The Remote Control Handset
All manuals and user guides at all-guides.com Connecting up and putting into operation UHF connection If your TV set does not have a Scart socket, the connection to the TV set is made via a coaxial cable (possibly via the video recorder) . •... -
Page 9: Tuning Uhf Channel
All manuals and user guides at all-guides.com Connecting up and putting into operation Tuning UHF channel / Checking operation • Switch on the satellite receiver via the on/off switch on the front of the unit. The LED display on the unit shows the last programme slot that was selected. •... -
Page 10: Receiver Operation
All manuals and user guides at all-guides.com Receiver operation Bedienung des Receivers In this chapter, you learn how to select TV and radio programmes using your re- ceiver, how to adjust the volume and how to programme the timer functions. In describing the functions, it is assumed that the receiver has already been prop- erly connected up by the specialist. -
Page 11: Adjusting Volume, Balance And Tone
All manuals and user guides at all-guides.com Receiver operation Note With the setting “2- or 3-digit programme selection“ there is a switch to the desired programme after approximately 3 seconds. Digits can be entered during this time. With the setting “free entry“ (in the above example) the receiver switches to the corresponding programme slot immediately after each input. -
Page 12: Stereo-/Mono- Channel Changeover
All manuals and user guides at all-guides.com Receiver operation Stereo- / Mono- / Channel changeover TV broadcasts can be transmitted in the two-tone channel method (e.g. original tone “English" on channel 1, “German" tone on channel 2). • Press the key. -
Page 13: Timer Setting
All manuals and user guides at all-guides.com Receiver operation • Alter the values step-by-step using the keys. Saving the settings After entering the time press the key to start the clock. Return to receive mode • Press the key to return to receive mode. •... -
Page 14: Daily And Weekly Repeated Switch-On
All manuals and user guides at all-guides.com Receiver operation are all shifted down by one line. Making changes If you want to alter a stored setting, place the cursor in the appropriate line by pressing the key. Enter the new data in the usual manner and save the new en- tries. -
Page 15: Video Recorder Playback (Vcr)
All manuals and user guides at all-guides.com Receiver operation On playback from the video recorder the LED display shows: -with the receiver switched on- -in standby mode- - VCR. On playback from the video recorder, you have the possibility of a brief switchover to satellite reception, in order to check the start of a broadcast, for example, without needing to switch off the video recorder. -
Page 16: Operation Without Remote Control
All manuals and user guides at all-guides.com Receiver operation • Exit from the menu with key the key. Radio programmes can be inserted, swapped or copied using the same method in “radio” mode. Operation without remote control If you happen to have mislaid the remote control handset, you can switch the re- ceiver between “TV”... -
Page 17: Programming Tv Programmes
All manuals and user guides at all-guides.com Programming TV programmes Programmieren von TV-Programmen The satellite receiver has already been factory pre-programmed for satellite re- ceiving systems with feed systems (receiving system) which have an oscillator fre- quency of 9.75 GHz. All of the programmes set up are listed in the table enclosed. If your satellite receiving system uses a feed system with a different oscillator fre- quency, the receiver only needs to be matched to the feed system oscillator fre- quency during the installation. -
Page 18: The "Video" Menu
All manuals and user guides at all-guides.com Programming TV programmes • Call up the audio menu: press keys in succession. • Switch between video and audio menus using key or the key . • Select the desired menu line using the keys •... - Page 19 All manuals and user guides at all-guides.com Programming TV programmes Orbit Position In the “Orbit Position“ menu entry, division of the satellites into orbit positions 1 to 4 is carried out. This dividing up is necessary for the signal selection with the 22 kHz, tone-burst or DiSEqC switching signal on reception from two (or more) satellites.
-
Page 20: Programme Name
All manuals and user guides at all-guides.com Programming TV programmes Programme name In the “Programme name“ line (in the video menu) you can enter a 5-character sta- tion identifier of your choice. • Using the key select the menu entry: “Programme name“. •... - Page 21 All manuals and user guides at all-guides.com Programming TV programmes Audio carrier frequency The following is a list of fixed, pre-programmed audio frequencies that can be se- lected using the keys. Mode Sound carrier frequen- Mode Sound carrier frequencies cies Stereo 7.02 / 7.20 MHz Mono (wide)
-
Page 22: Programming Radio Programmes
All manuals and user guides at all-guides.com Programming radio programmes Programmieren von Radio-Programmen Programme providers are continually bringing out new radio programmes for broadcast via the satellites. The “Radio“ menu allows you to store these pro- grammes. The settings for radio programmes in “Radio“ mode are carried out in the same way as for the “TV“... -
Page 23: Initial Settings
All manuals and user guides at all-guides.com Initial settings Grundeinstellungen In the initial setup menu, matching of the satellite receiver to the satellite receiving system is carried out. Important The receiver has already been factory pre-programmed for standard satellite re- ceiving systems. -
Page 24: Osd Language
Here you can turn off the power supply for the feed system if this is implemented by an external power supply and signal selection is likewise not carried out by means of the LNB supply voltage (e.g. Kathrein single-cable feed system UAS 330). -
Page 25: Remote Control Handset
As a result, you can easily install the UFD 400 on other receiving systems without needing to reprogramme every single programme slot. You only need to set up the particular oscillator frequencies that your receiving system uses. -
Page 26: Diseqc Menu
LNB selection and signal selection. The “DiSEqC“ control signal is, in fact, a special form of modulation (pulse-width modulation) of the already existing 22 kHz signal. The UFD 400 receiver is equipped with: • DiSEqC tone burst (also termed Simple DiSEqC or just DiSEqC) •... -
Page 27: Tone Burst And Diseqc Signal
All manuals and user guides at all-guides.com Initial settings (factory preset) See also video setup menu, menu lines: Polarisation and Orbit Position. Tone burst and DiSEqC signal If more than four control criteria are needed in a receiving system, a DiSEqC control signal is required. - Page 28 Here control and communication between the receiver and the Kathrein “UFO mi- cro" system is effected via the return path of the coaxial cable. If the UFD 400 receiver is operated on a “UFO micro“ receiving system, an “ On " setting must be made in menu entry “UFO micro".
-
Page 29: Switching Over Remote Control's Command Set
Note With remote control handsets that have 24 keys (remote controls of the 200-series receivers from Kathrein) code numbers 001, 002 and 003 are to be entered in place of codes 901, 902 and 903. -
Page 30: Features
All manuals and user guides at all-guides.com Features The UFD 400 receiver is equipped with the following features: • 250 programme channel memory • Satellite input frequency range from 920 MHz to 2150 MHz • Freely selectable oscillator frequencies, thus suitable for all feed systems •... -
Page 31: Specifications
All manuals and user guides at all-guides.com Specifications Technische Daten UHF characteristics Sat IF frequency range 920 to 2150 MHz Input level range 48 to 78 dBµV IF frequency 479.5 MHz IF bandwidth 27 MHz FM threshold 7 dB max. Video Frequency range 20 Hz to 5 MHz... -
Page 32: Scart Socket Assignments
All manuals and user guides at all-guides.com Specifications General Unit dimensions (B/H/D) 310 / 71 / 165 mm Weight approx. 1.3 kg Temperature range Ambient temperature +5 °C ... 40 °C Accessories Infrared remote control 2x 1.5 V batteries, type: LR 03, size: AAA (micro) Scart socket assignments Signal Pin No. -
Page 33: Connection Example
All manuals and user guides at all-guides.com Connection examples / Service note The best picture quality is obtained if you connect the satellite receiver, TV set and video recorder by means of Scart cables. A stereo TV set also allows you to receive the sound in stereo. Connection of a Sat receiver to a TV set and video recorder with Scart cables, a hi- fi for reception of Sat radio programmes and a decoder for Pay-TV-Programme (e.g. - Page 34 All manuals and user guides at all-guides.com KATHREIN-Werke KG Telephone ++49 80 31 18 40 Fax ++49 80 31 18 43 06 Anton-Kathrein-Straße 1-3 P.O.B. 10 04 44 D-83004 Rosenheim...
Need help?
Do you have a question about the UFD 400 and is the answer not in the manual?
Questions and answers