Advertisement
3.
If installing the FC4–48, go to step 4.
For FC4–16 and FC4–32 models (see
a. Open the ejectors to approximately 45 degrees.
b. Align the flat side of the port blade inside the upper and lower
rail guides in the slot, and slide the port blade into the slot,
with slight pressure to the left, until it is firmly seated.
4.
For FC4–48 models (see
a. Adjust the ejectors to the open position.
b. Align the flat side of the port blade inside the upper and lower
rail guides in the slot.
c.
Slide the port blade into the slot, until it is firmly seated.
!
!
8
7
6
5
4
!
3
15
2
14
1
13
!
12
!
!
11
15
10
14
9
13
8
12
7
11
6
10
k
s
Lin
M b/
00
5
10
/1
9
s
C P
k
M b/
iv e
Lin
A ct
4
00
8
/1
10
C P
iv e
A ct
3
7
2
6
1
5
0
4
F C
3
4
3 2
F C
2
1 6
1
0
4
C P
4
4
C P
F C
1 6
H z
- 6 0
5 0
2 A
C 1
V A
4 0
0 -2
2 0
H z
- 6 0
5 0
2 A
C 1
V A
4 0
0 -2
2 0
Figure 5 Installing an FC4–48 Port Blade
Callouts
1. SAN Director chassis
2. FC4–48
5.
If installing the FC4–48, go to step 6.
For FC4–16 and FC4–32 models (see
a. Push the handles toward the center of the port blade, closing
the ejectors.
b. Verify that the handle's levering action properly seats the port
blade in the slot.
6.
For the FC4–48:
Adjust the ejectors to the closed position (see
them away from the center of the port blade.
Figure
4).
Figure
5):
1
!
!
1 0
9
4
P L
Y
U P
R S
W E
P O
!
!
3
2
Y
P L
U P
R S
W E
P O
3
!
!
!
47
2
P L
Y
23
U P
46
R S
22
W E
P O
45
21
44
20
4
F C
43
3 2
4
19
42
!
18
41
!
17
40
16
39
15
1
1
L Y
L Y
38
P P
P P
14
S U
S U
R
R
37
W E
W E
P O
P O
13
36
12
35
11
34
10
33
9
32
8
4
31
7
30
6
29
5
28
4
27
3
26
2
25
1
24
0
25223a
3. Upper ejector
4. Lower ejector
Figure
4).
Figure
5) by pulling
7.
Tighten the thumb screw inside each handle using the Phillips
screw driver.
IMPORTANT:
The upper and lower thumb screws must be completely
tightened, and the upper and lower ejectors must be in the
closed position for the FC4–48 to power on.
8.
If installing the FC4–48, go to step 9.
For FC4–16 and FC4–32 models (see
a. To power on the port blade, move up the slider switch in the
top ejector.
b. Verify that the slider switch covers the thumbscrew.
9.
For the FC4–48:
Verify that the power LED on the port blade displays a steady
green light (it might require a few seconds to turn on). If it does
not turn on, ensure that the port blade is firmly seated and that the
thumb screws are tight.
The LED patterns might temporarily change during POST and other
diagnostic tests.
10.
Install SFP transceivers and cables in the port blade, as required.
11.
Refer to the HP StorageWorks SAN Director installation guide for
different ways to manage cables, including:
• Routing directly down, through the cable management tray,
instead of across adjacent blades to keep LEDs visible.
• Installing cable channels on the sides of the cabinet
• Installing patch panels
IMPORTANT:
Disassembling any part of the port blades voids the part
warranty and regulatory certifications. There are no
user-serviceable parts inside the port blade.
Waste Electrical and Electronic
Equipment (WEEE) directive
Page 4
Figure
4):
Advertisement
