Related Manuals for Kellfri 27-HRT160
Summary of Contents for Kellfri 27-HRT160
- Page 1 27-HRT160 HEDGE TRIMMER Read this manual carefully before using the product! Translated from the original...
-
Page 2: Product Information
INTRODUCTION Thank you for choosing a product from Kellfri AB. By following general safety information, operating instructions and common sense, you will have many years of enjoyable use of the product. Kellfris equipment and products are aimed to be use by active farmers with high demands on functionality. -
Page 3: Product Safety Information
Your retailer The general safety instruction is also available from Kellfris website: www.kellfri.co.uk Do not use this equipment if you are feeling sick, tired or in influence of alcohol. Nor if you are under the influence of strong medications or drugs, suffering from strong depression or severe mental illness. - Page 4 WARNING! Never use a tool or product with defective safety equipment. • Never leave the equipment with the tractor engine running. Turn off the engine and ap- ply the parking brake when you leave the piece of equipment, even for a short while. •...
-
Page 5: Personal Protection
PERSONAL PROTECTION Always wear suitable clothing and footwear. Do not wear loose clothing or jewelry when using the machine. Remember to put up long hair when operating rotating machines. Wear protec- tive gloves, to prevent risking burns on contact with hot surfaces such as exhaust system, and to avoid oil and gasoline on the skin. -
Page 6: Warning Labels
WARNING LABELS Make sure that the warning labels are always visible, clean the warning labels if necessary. Do not wash with high pressure washer directly on the warning label. If any part of the decal is worn or label becomes frayed or otherwise unreadable, order new decals. SYMBOL EXPLANATION Read the instruction manual! Before starting the operation. - Page 7 BEFORE USE Read the safety information and instruction manual carefully. Be sure you understand the safety measures, instruction manual and warning labels. Use common sense when operating the machine and use appropriate personal protective equipment. Always check the performance and the machine combination that are used. It’s highly impor- tant these matches in a satisfactory manner.
- Page 8 RISKRISKS AND HAZARDS OF USE OF MOWING MACHINE Risk of crushing Bystanders may be injured when the machine is lowered to the cutting position. The machine has crushing points around the hinge areas and between the three-point hitch mount and the main body.
-
Page 9: Operation
The potential for slip-and-fall accidents can be significantly reduced by using good judgment. All unprotected rotating machinery is a potential for accidents. Damage usually occurs when loose clothing or long hair caught and wrapped around rotating parts such as transmission shafts or drive shafts on the machine. -
Page 10: Safety Precautions During Operation
SAFETY PRECAUTIONS DURING OPERATION • It is forbidden to use the machine as a lifting instrument. • It should not be used for excavation of any kind or cutting other materials than described in this manual. • Before operation, make sure that the PTO shaft is correctly mounted and cannot come loose during operation. -
Page 11: After Use
Attach the machine to the tractor’s 3-point lift, make sure it is well-attached Connect the pump to the PTO, make sure it can not loosen and all the hoses are not bent or caught in any rotating parts of the tractor or machine. The ’lever kit’... - Page 12 35-HTR160 TECHNICAL DATA A1 A2 B1 B2 C1 C2 ° ° ° MIN. MAX. 1500 480 320 370 550 280 100 300...
-
Page 13: Transport And Storage
LUBRICATION OF JOINTS Lubricte regularly, at least 2 times a year or every time service / maintenance is performed For ordering spare parts : Contact Kellfri Service RECYCLING Disposal of the product, disassemble and transport to the municipality’s recycling station. - Page 14 ASSEMBLY Packaging measurement: LxWxH 1100x540x2440 mm Warning! Risk of crushing! Make sure that the machine does not tip over during assembly! The machine is delivered partly assembled. Use appropriate lifting instrument when lifting the machine from its packaging box. make sure that the machine is steady and cannot tip over.
- Page 15 Install the cutting head to the lifting arm, then tighten all bolts. NOTE! The head of the bolts should be mounted on the side where the cutouts are located (shown with ar- rows in the picture) Then connect the hydraulic hoses on the hydraulic motor...
- Page 16 Check that all hydraulic couplings and hydraulic hoses are intact, tighten the con- nections if necessary. Fill the oil tank with hydraulic oil approximately 20L. Attach the machine to the tractor’s three point hitch and connect the pump to the PTO.
-
Page 17: Hydraulic Diagram
HYDRAULIC DIAGRAM Cylinder 1 Cylinder 2 Hydraulic motor Cylinder 3 Valve package Pump Cylinder 1 - Beam (R35-HRT160.081) Cylinder 2 - Folding arm (R35-HRT160.087) Cylinder 3 - Bom cylinder (R35-HRT160.075) Hydraulic motor Hydraulic tubes - J,K,L LEVER FEATURES lifting arm folding arm knife beam hydraul motor... -
Page 18: Cutting Head
CUTTING HEAD 56 57 46 47 48 41 42 43 44 45 15 25... - Page 19 Description Description Bolt M12x60 Bearing 6009 Hydyaulic motor (BMP502AD) Ring 45 Oil pipe connector Bearing seat Nut M12 Ring 75 Square hole washer Washer 12 Connection plate Nut M14 Bolt M12x45 Washer 14 Hydraulic motor support plate Hitch frame Bolt M12x45 Seperator Flywheel Bolt M14x40...
-
Page 20: Base Frame
BASE FRAME... - Page 21 Description Description Bolt M10x25 Oil tank cover Spring washer 10 Washer 6 Washer 10 Screw M6x10 Chain hanging plate Air plug G 3/8 step-up gear box Return oil filter Oil hose (pump to valve) bonded washer 42 Screw M8x25 Oil filter connector Spring wahse 8 Oil hose (valve to oil filter) Motor connector for oil...
-
Page 22: Lifting Arm
LIFTING ARM 2 26 Description Description Pression plate Bolt M16x90 Bolt M 8x45 Washer16 Nut M16 Small arm bonded washer 14 BOLT M20X190 Washer20 Hinged boltsM14×1.5 Swing arm cylinder Nut M20 Oil hose( valve to small arm) Cylinder for small arm Bolt M16x120 Oil hose( valve to big arm) Nut M14... - Page 23 Complaint form We are grateful for your help pointing out any inaccuracies in the Kellfri product delivered to you. Before making a complaint read Kellfris general warranty and sales conditions in our catalog as well as the enclosed User’s manual that comes with the machine.
-
Page 24: Ec Declaration Of Conformity (Original)
You are always welcome to give your feedbacks, reviews or ask us about our equipment and products. Kellfri AB is constantly working on further developing their products and therefore reserves the right to modify, among other things the design and appearance without further notice.
Need help?
Do you have a question about the 27-HRT160 and is the answer not in the manual?
Questions and answers