Subscribe to Our Youtube Channel
Related Manuals for SI 5 Motorized
Summary of Contents for SI 5 Motorized
- Page 1 5 Motorized Owner’s Manual Screen Innovations Control - DCT with 12v & IR Trigger 9715-B Burnet Rd, Suite 400 Austin, TX 78758 512.832.6939 www.screeninnovations.com INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Parts In The Box � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1 - 2 Flush 110 v / 220 v AC - Flush L / Suspended Brackets . -
Page 3: Parts In The Box
PARTS IN THE BOX - FLUSH - 110v / 220v AC L-Bracket / Suspended Ceiling Bracket Screen Suspended Ceiling Bracket Kit Front Closure Rear Closure L - Brackets * NOTE: Screws are provided to mount to wooden structural supports only. If other substrate is present then installer must provide appropriate fasteners. -
Page 4: 110V / 220V Ac Pigtail Power
PARTS IN THE BOX - EXTERNAL - 110v / 220v AC PRE-WIRING - 110v / 220v AC - Pigtail Power 1. Make sure an appropriate junction box or power receptacle is located within 5ft of the installation location. 2. Wire in the pigtail power cable at the junction box per electrical code standards. Screen 110V White NEUTRAL... -
Page 5: Mounting Case Type
MOUNTING CASE - TYPE INSTALLATION - FLUSH Measure Case & Cut Out Pocket FLUSH L FLUSH SUSPENDED Measure the case length and record the measurement. If pre constructing the pocket then Installation requires two or more people. Use proper lifting techniques refer to the screen builder for the F dimension for your particular size screen. -
Page 6: Mounting Flush L-Brackets
INSTALLATION - FLUSH INSTALLATION - FLUSH Add End Flange & Remove Weight Bar Lock Mounting Flush L-Brackets FLUSH L FLUSH SUSPENDED FLUSH L Mount the L brackets either to a vertical or horizontal structural support as shown. Make Line up the holes on the removable flanges with the holes in the end plates. Then install sure brackets are level and plumb. -
Page 7: Hang Case And Raise Up Flush L - Brackets
INSTALLATION - FLUSH INSTALLATION - FLUSH Hang Case on L-Brackets and Raise Up Mounting Flush Suspended Brackets FLUSH L FLUSH SUSPENDED Install minimum 3/8’’ threaded rod to structural members in the ceiling per the drawing Installation requires two or more people. Use proper lifting techniques below. - Page 8 INSTALLATION - FLUSH INSTALLATION - EXTERNAL Hang Case on Suspended Brackets and Raise Up Measure case & Mount L Brackets FLUSH SUSPENDED EXTERNAL Raise the case up and guide the threaded rods through the holes in the suspended Measure the case length and record the measurement. ceiling brackets.
-
Page 9: Trim Installation Flush
INSTALLATION - EXTERNAL TRIM INSTALLATION - FLUSH Remove Weight Bar Lock, Hang Case and Raise Up Flush Trim Install EXTERNAL FLUSH L FLUSH SUSPENDED Hook the larger front closure into the case opposite the weight bar and then rotate Remove the tagged Weight Bar Locks. down to secure. -
Page 10: Trim Installation External
TRIM INSTALLATION - FLUSH TRIM INSTALLATION - EXTERNAL Flush Trim Locking Fascia Install & Fascia Lock FLUSH L FLUSH SUSPENDED EXTERNAL Insert the bumpers into the holes in the endplates. Press the pin in the bumper until you Hook the front trim into the case opposite the weight bar and then rotate down to secure. feel a SNAP indicating the bumper is secured. - Page 11 TRIM INSTALLATION - EXTERNAL CONTROLS - Inputs / Contact Closures Trim Install EXTERNAL RJ45 inputs(3) have been provided which all operate the same. An additional 1/8’’ (3mm) Use the 9/64’’ hex key to loosen the two screws securing the fascia lock. Then slide the mono low voltage trigger is also provided.
-
Page 12: Wiring (Wall Switch)
CONTROLS - WIRING - Wall Switch CONTROLS - SETTING THE LOWER LIMITS Connect the RJ45 end of the provided wall switch cable to any port on the screen. Wall Switch buttons Back of the switch Connect the smaller RJ9 port to the back of the wall switch. UP DN CMN 5vDC Send Motor to Upper Limit... -
Page 13: General Operation
CONTROLS - SETTING THE LOWER LIMITS WALL SWITCH - GENERAL OPERATION DO NOT press and hold the stop button at any time. It will record and intermediate position which Hold the down button on the wall switch to move the screen down to the desired lower will not be usefull for your projection screen. -
Page 14: Reverse Screen Direction
WALL SWITCH - REVERSE SCREEN DIRECTION CONTROLS - IR REMOTE If the screen moves opposite direction from the button pressed. Then use the following Plug in the included IR eye to any of the RJ45 ports on the case. Then use the included remote to procedure to reverse the motor direction. -
Page 15: 3Rd Party Control Systems
ADJUSTING THE SCREEN TENSION IR Hex Codes Use a 3rd party universal remote to control the screen via the IR eye. SI recommends using a Press in the button and turn knob counter clockwise untill the string is loose. learning remote to learn the codes from the included IR remote. However, the IR HEX codes can be used to manually program them into your universal remote or 3rd party control system. -
Page 16: Troubleshooting
Also, lightly brush off the front of the screen. When down An intermediate stop was set Call SI Customer Support to fix at 512.832.6939, button is pressed, for the motor. Opt. 1 Wrinkles near bottom... - Page 17 NOTES...
Need help?
Do you have a question about the 5 Motorized and is the answer not in the manual?
Questions and answers