Advertisement
Quick Links
OPERATING MANUAL
Cole-Parmer
Mixer Head Model Numbers
50007-10, 50007-20, 50007-30, 50007-40,
Mixer Controller Model Numbers 50007-00
Cole-Parmer
Mixer Head Model Numbers
50008-10, 50008-20, 50008-30, 50008-40
Mixer Controller Model Number 50008-00
Cole-Parmer
625 East Bunker Court
Vernon Hills, Illinois U.S.A. 60061-1844
Toll Free: 800-323-4340
Phone: 847-549-7600
Fax: 847-247-2929
www.coleparmer.com
E-mail: techinfo@coleparmer.com
®
Stir-Pak
&
®
ServoDyne™
&
-- 1 --
®
Version 11Nov08 Rev1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Cole Parmer Stir-Pak 50007-10
Summary of Contents for Cole Parmer Stir-Pak 50007-10
- Page 1 OPERATING MANUAL ® ® Cole-Parmer Stir-Pak Mixer Head Model Numbers 50007-10, 50007-20, 50007-30, 50007-40, & Mixer Controller Model Numbers 50007-00 ® Cole-Parmer ServoDyne™ Mixer Head Model Numbers 50008-10, 50008-20, 50008-30, 50008-40 & Mixer Controller Model Number 50008-00 Cole-Parmer 625 East Bunker Court Vernon Hills, Illinois U.S.A.
-
Page 2: Safety Precautions
SAFETY PRECAUTIONS • High voltages exist and are accessible in the controller. Contact Cole-Parmer for servicing. • Do not operate mixers where explosive vapors or flammable materials exist. Death or serious injury could result. Check NEC and local codes before installing. - Page 3 INTRODUCTION The Stir-Pak 50007-series heavy-duty modular mixing system covered in this manual consists of four different mixer heads and a analog controller 115VAC operation. The ServoDyne 50008-series digital modular mixing system consists of four different mixer heads and a precision digital controller for 115VAC operation. The following chart cross-references the model number, operating speed range and torque rating of the mixer heads and the compatible controller.
- Page 4 50008-00 SERVODYNE CONTROLLER/DISPLAY FUNCTIONS Four-digit LED display LEDs indicate the shows selected mixing function being displayed time, mixing time (time, rpm, or torque). A remaining, rpm, and flashing time or torque torque values. light and audible alarm indicate that a limit condition has been reached.
-
Page 5: Installation And Setup Procedures
INSTALLATION AND SETUP PROCEDURES The mixer heads are equipped with an adjustable-tilt mounting assembly. The mounting assembly is designed to be attached to an optional mixer support stand or tank clamp. Components supplied as part of the mixer package include the following: •... - Page 6 Installation Using a Support Stand 1. Set up support stand in accordance with the manufacturer’s instructions. 2. Attach a double (rod) clamp to the vertical rod on the support stand and tighten clamp screw. (See Figure 4) 3. Slide rod of adjustable-tilt mounting assembly into clamp and secure with clamp screw. 4.
- Page 7 Figure 4: Typical mixer setup using a support stand and pivot mount (ServoDyne system shown) Note: The controller can be placed on any flat surface within 6 feet of the mixer head or can be mounted on a support platform (not supplied) or a pivot mount (not supplied). Refer to the ACCESSORIES section for part numbers.
- Page 8 For high-speed mixer head, slide the 0.375 inch mixer shaft through the collet and tighten collet. Be sure only 0.375 (+/-0.0005) inch shafts are used. Contact Cole-Parmer or your dealer for obtaining the proper shaft size. Refer to the ACCESSORIES section for the part numbers.
- Page 9 5. Position the height of the mixer head on high-sp ed models by loosening the collet and positioning the shaft. The controller can be placed on any flat surface within 6 feet of the mixer head and can be Note: mounted on a support platform (not supplied) or a pivot mount (not supplied).
- Page 10 50007-00 STIR-PAK CONTROLLER OPERATION FWD-OFF-REV Switch FORWARD-OFF-REVERSE POWER ON SPEED SWITCH INDICATOR CONTROL In the FWD position, the shaft will rotate in a LIGHT counterclockwise direction when viewed from the impeller. The center or OFF position removes power from both the controller and mixer head. In the REV position, the shaft will rotate in a clockwise direction when viewed from the impeller.
- Page 11 Set Run Time The use of the TIME b utton in conjunction with the buttons permits entry of a desired mixing time. Pressing the button once when already in the time display mod e cause s the le (minutes) digit to flash, pressing the button once again causes the right two (s econ...
- Page 12 Specificatio ns – Mixer Head Direct ion of Rotation: Bi-directional controlled with the FWD-OFF-REV switch 50007 Stir-Pak Series CCW (Viewe d from Impeller end) 50008 ServoDyne Series Speed Range: 2 to 180 rpm 3 to 180 rpm 50007-10 50008-10 9 to 900 rpm 20 to 900 rpm 50007-20 50008-20...
- Page 13 Specifications – Controller Output: Model aximu Maximum Maximum Volt Current, Amps Powe r, Watts 50007-00 50008-00 Speed regula tion: Model Line Load ±1% F.S. ±2% F.S ± F.S. 5000 7-00 ±0.25% F.S. ±0.25% F.S. ±0.25% F.S. 50008-00 Four-digit, seve egment LED Display 9 minutes, 59 se conds...
- Page 14 MAINTENANCE AND TROUB LESHOOTING intenance is limited to replacement of motor brushes on the mixer head, replacing the fuse on the cont roller, and cle anin g the unit. If a faul t is detect ed when trou bleshooting and ca nnot be corrected by the su ggested...
- Page 15 Replacement Parts No user-serviceable parts are inside of this instrument. Refer servicing to Cole-Parmer or your dea ler. The following parts are user-replaceable: Description For model(s Part Number 50007-00 04552-91 Speed Control Knob 50008-00 77500-25 Fuse, T3.15A 07520-04 Moto r Brushes (2)
-
Page 16: Warranty
Warranty Card. PRODUCT RETURN To limit charges and delays, contact Cole-Parmer or manufacturer for authorization and shipping instructions before returning the product, either within or outside of the warranty period. When returning the product, please state the reason for the return. For your protection, pack the product carefully and insure it against possible damage or loss.
Need help?
Do you have a question about the Stir-Pak 50007-10 and is the answer not in the manual?
Questions and answers