Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LINK-MI LM-TN701
Summary of Contents for LINK-MI LM-TN701
- Page 1 Mobile Phone Sync Screen Rotator LM-TN702 User Manual...
-
Page 2: Chapter I Installation Notes
When installing, please note the following: 1, the product description This document is general-purpose operating instructions of LM-TN701, LM -TN702, LM -TN703 three types, due to different model's features of product are not the same, if in doubt please contact us or refer to the product specifications of appropriate type. Here is the main... - Page 3 cable should keep from trample or extrusion, to prevent the risk of leakage or short circuit. 5, Signal cable: Inserting or pulling the signal line to the device, the device needs to be outage, so as not to damage the device. Hot plug caused damage not covered under warranty. 6, Vents: The outer surface of the device may have openings for heat dissipation, do not block these openings, in order to avoid heat build-up, the risk of damage to the equipment or cause fire.
-
Page 4: Chapter Ii Product Introduction
device and disconnect the power supply immediately, handled by the professionals; This device is not suitable for non-professionals to operate the debugger, users are subject to professional training and guidance. Please read carefully before using and this manual should be properly preserved for later use. Chapter II Product Introduction 1 Overview: LM–TN70x series fold line rotator is a high-performance switcher, the internal contain... -
Page 5: Panel Description
Panel Description Chapter III Machine Installation 1 Unpacking Check the host and accessories. Including the host, power cable, remote control, warranty card, manual. 2 Install the machine 2.1, setting the display unit: the LCD TV or other display device's input signal is set to HDMI status;... -
Page 6: Chapter Iv Product Settings
2.3, connect input signal Product support 1 channel VGA, 2-way DP, 4-way HDMI and 1 left and right channel audio with binding VGA signal input. D1, D2, D3, D4 port can connect directly with PC, Blu-ray DVD and other equipment through ordinary HDMI cable; D2, D3, D4 can be connected with a simple Micro USB transferred HDMI cable, so that smart phones with MOBILE PHONE PORT-enabled can display on display unit , Micro USB transfer HDIM line as shown below: 3. -
Page 7: Menu Settings
6: HDMI or MOBILE PHONE PORT signal of D4 port; 7: DP signal of D5 port; SOURCE 2, through the button to switch: ↑ ↓ SOURCE Press the button of remote control pop-up below menu, the navigation keys move the red mark cursor to the signal source you desired, then click button to select the →... - Page 8 with display unit; 3, automatic adjustment For not full screen, the image deviation of VGA input signal, a key correction by left or right navigation keys; 4, brightness ← → navigation keys to adjust the brightness of the image ; 5.
- Page 9 Chapter V RS232 serial control Except for product can be controlled by the remote control and buttons of chassis, also can be controlled by RS-232 serial ,that is the user can switch the signal, mode selection, output serial assistant resolution of the machine through enter code after download , the following are the serial setting and frequently-used control codes: Baud rate: 9600...
-
Page 10: Specification
Specification Input Signal 1x VGA HD15 port, supports 640x480@60Hz to 1920x1200@60Hz 2x DP Display Port 1.1 4x HDMI HDMI 1.4(HDCP 1.3), Compatible with smart phone signal 1x Audio 3.5mm earphone port, supports L/R stereo audio, bound with VGA Video signal Output Signal 1x HDMI HDMI 1.4(HDCP 1.3), 1920x1080/60Hz,... -
Page 11: Product Contents
Product Contents 1. One Mobile Phone Syn cscreen Rotator 2. One IR cable 3. One remote controller 4. One power adapter 5. One instruction manual... - Page 12 SHENZHEN LINK-MI TECHNOLOGY CO., LTD E-mail: sales@link-mi.com WWW.LINK-MI.COM...
Need help?
Do you have a question about the LM-TN701 and is the answer not in the manual?
Questions and answers