Reset To The Default Setting (Except For Parental Setting); Troubleshooting Guide - Sylvania DVC865G Owner's Manual

Reset to the Default Setting (Except for PARENTAL Setting)

1
Press [SETUP] in the
stop mode.
SETUP
STOP
<SETUP MENU>
SETUP
QUICK
CUSTOM
INITIALIZE

Troubleshooting Guide

If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.
PROBLEM
No power.
This unit does not
respond to the remote
control.
Poor picture or noise.
Timer recording is impos-
sible.
Cannot go into record
mode.
Playback picture is partially
noisy.
Cannot view a tape but
the audio is OK.
No or poor, playback
picture.
TV programs cannot be
seen normally.
Video or color fades in
and out when making a
copy of a video tape.
Cannot remove the tape.
No picture.
Disc cannot be played.
No sound.
Distorted picture.
Audio or subtitle language
does not match the setup.
The camera angle cannot
be changed.
Audio or subtitle language
cannot be changed.
"Prohibited icon" appears
on the screen, prohibiting
an operation.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner's Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
E8A00UD_E8C00UD.indd 23 E8A00UD_E8C00UD.indd 23
2
Select "INITIALIZE".
or
SETUP
QUICK
CUSTOM
INITIALIZE
Information
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote control.
• You have to be within 23 feet (7m) of this unit.
• Check if the right mode is selected. If it's not in the right mode, press [DVD] or [VCR], whichever you need, on the remote control.
• Check if a cassette tape is in this unit.
• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then if you hear some signal sound from the radio
in response to your pressing buttons on the remote control, the remote control is working.
• Interference signal may be received. Change the position and orientation of the unit.
• Make sure the Timer Recording is set correctly.
• Make sure appears on the front panel display. If not, press [SUBTITLE/T-SET].
• Make sure the VCR clock is set correctly.
• Make sure the tape has a record tab. If needed, cover the hole with adhesive tape.
• Activate this unit in VCR mode. Press [VCR] on the remote control so that the VCR OUTPUT light is lit.
• Adjust tracking control for a better picture by pressing [CHANNEL L/K]] on the unit or [SKIP/CH. G/K, H/L] on the remote control.
• Head cleaning may be necessary. Refer to "AUTO HEAD CLEANING".
• Make sure the VCR is not in the Menu mode.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
• Re-check the ANT-IN and ANT-OUT connections. See the front page and page 6.
• Press [VCR].
• Press [VCR] on the remote control to activate it in the VCR mode. Check if the VCR OUTPUT light is lit, then set it to the TV position by press-
ing [VCR].
• You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
• Check if this unit is in the VCR mode. If not, press [VCR] on the remote control to switch the mode.
• Connect the video cable fi rmly.
• Insert a correct video disc that plays on this unit.
• Press [DVD] on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features.
• Set PROGRESSIVE correctly. Turn it on only if your TV has progressive scan and you are using the Component Video connections between
the unit and the TV. Disable progressive scan for all other connections. (See page 7.)
• Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fi ngerprints, scratches, or dusts on its surface.
• Connect the audio cable fi rmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
• Check if the INTERLACE/PROGRESSIVE mode correctly according to your TV. See pages 20-21.
• The selected language is not available for audio or subtitles on the DVD.
-This is not a malfunction.
• The DVD does not contain sequences recorded from different camera angles.
-This is not a malfunction.
• The DVD does not contain audio source or subtitles in the selected language.
-This is not a malfunction.
• That operation is prohibited by this unit or the disc.
-This is not a malfunction.
3
Select "YES".
or
ENTER ENTER ENTER
SETUP INITIALIZE
Initialize?
NO
YES
CORRECTIVE ACTION
– 23 –
4
To exit the
menu
SETUP
ENTER ENTER ENTER
Press Hint
twice.
• When you cancel
to initialize at step
3, select "NO".
EN
2006/08/18 13:11:35 2006/08/18 13:11:35