Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Inax RS Series
Summary of Contents for Inax RS Series
- Page 4 10. Avoid using front and rear washing functions excessively or for long periods of time as such overuse may increase the possibility of washing away desirable resident bacteria and causing an imbalance of bacteria in your body. If you are pregnant, are being treated for a gynecological condition, develop excessive irritation in the area of use, or if you have questions, please speak to your doctor before beginning or continuing use of the product.
-
Page 5: Product Description
2. Product description This product provides features to enhance personal toilet hygiene and comfort. This product features include a posterior wash, a bidet, a warm air dryer, and a seat heater, as well as controls for these functions. This product consists of a body (with heated toilet seat, toilet seat lid, warm water tank, and power cord), hardware to mount the body on a toilet and connect it to the toilet water supply and this installation and use manual. -
Page 6: Installing This Product
3. Installing this product Installation requirements Before installing this product, ensure that each of the following installation requirements is met. Product carton contents Remove the parts from the product carton and make sure all the parts in the parts list (below) are present. - Page 7 Ground fault circuit interrupter A ground fault circuit interrupter must be installed in the circuit that supplies power to this product. Power supply This product is for use on a nominal 220 V circuit. Use a 220 V, 50 Hz power supply. The maximum power consumption is 305 W.
- Page 8 Checking the toilet 1. Measure the size of the toilet. Depending on the toilet, it may not be possible to mount 14 to 15.7 cm this product on it. Make sure the toilet's dimensions are as shown in the figure at right. φ1.5 cm or more 39 cm or less 5 cm or more...
-
Page 9: Names Of Parts
Names of parts Overall view <Bottom of body> Caution label Remote control unit Deodorizer (See page 10.) Toilet seat lid cartridge cover Deodorizer Tank cartridge Tank water supply pipe Junction fitting Marking label Water shutoff valve Occupied seat sensor Strainer Nozzle (for bidet) (See below.) Nozzle (for posterior) -
Page 10: Operation Panel
Operation panel STOP SHOWER BIDET Stops posterior washing, Use for posterior washing. Use for bidet washing. Use when drying wet parts. bidet washing, and drying (See page 25.) operations. MASSAGE Alternates spray strength between strong and weak. POWER POWER SAVE STRENGTH Pressing the stop switch Pressing the toilet seat... -
Page 11: Installation
Installation 1. Installation of branch fitting (2) Remove the existing water supply pipe. Branch fitting Installation diagram 1) Loosen the cap nut at the tank. Packing A small amount of water Tank (color: black, may spill from the pipe Cap nut thickness: 2 mm) Supply pipe when loosening the cap... - Page 12 (2) Attach the water supply pipe. 1) Place the cap nut for the tank and branch fitting, split compression ring, slip washer, and packing (color: black, thickness: 4 mm) on the shortened water supply pipe and Supply pipe Branch fitting insert the pipe into the branch fitting.
- Page 13 4. Installation of the shower toilet (1) Remove the existing seat. Installation diagram Seat mounting bolts 1) Remove the nuts from the seat mounting bolts, the slip washers, and rounded Mounting brackets packing. Slide plate 2) Raise the seat and remove it by lifting the seat mounting Bushing bolts.
- Page 14 5. Attachment of the water supply hose for the shower toilet (at the branch fitting) (1) Remove the Installation diagram Branch fitting Example of water supply from the floor protective covers O-ring Branch from the ends of fitting Protective the water supply covers hose and insert the hose into the...
-
Page 15: Mounting The Remote Control
7. Positioning the remote control unit (1) Open the back cover of the remote control Back cover unit and insert the batteries (two AA size batteries). Battery (2) Place the remote control unit in the position you would like it to be in, sit down on the toilet seat and press the stop switch. -
Page 16: Trial Operation
Trial operation (Follow the procedure below after installation work is completed.) 1. Insert the power plug in the outlet. Confi rm that the power lamp on the body is lit. 220V Power plug 2.Check the shower and bidet spray. (1) Check the shower washing operation. 1) With your forearm resting on the toilet seat, press the SHOWER button. - Page 17 3. If flushing begins to weaken,or if the shower spray seems to be getting weaker, clean the strainers. (1) Turn the water shutoff valve to the right to close it. Turn clockwise. As the water shutoff valve is pre-adjusted, remember the original position (how much it is turned).
-
Page 18: Using This Product
4. Using this product Safety precautions Observe these precautions to prevent possible injury or damage. Do not pull the power plug out of the wall For care of plastic parts, do not use any outlet by pulling on the power cord. This could cleansers which are not safe to use on damage the power plug or power cord and toilet seats. - Page 19 Do not apply unnecessary force to the body If there is risk of water lines freezing, water supply hose. Doing so could damage it implement the freeze prevention methods to and cause water to leak. prevent damage. (See page 35.) Do not urinate on the nozzle.
-
Page 20: Other References
Other references A toilet seat cover or toilet seat lid cover can Before and after washing and when the water cause the occupied seat sensor to either remain temperature adjustment button is pressed, etc., on continuously or not go on at all, leading to water is sprayed out around the nozzle, but this faulty operation. - Page 21 Using this product functions 《Remote control unit》 Depending on the model, some functions (marked with a star, ☆ ) may not be included. ■ Main operation panel BIDET Remote control transmitter SHOWER Blows air for drying. Use for bidet washing. Use when washing your (See page 25.) Press again for wide range posterior. washing.(See page 23.) Press again for wide range washing.
-
Page 22: Preparations Before Use
《Preparations before use》 For an even more comfortable use, check the following operations before using this product. ■ POWER (Turning the power on/off) Press the POWER button to turn the power ON or OFF. * If the power is ON, the power lamp on the indicator panel will light * When you insert the power plug into the power outlet for the first time after purchasing this product, the power is automatically set to "ON". -
Page 23: How To Use Basic Functions
《How to use basic functions》 ■ Shower ■ Bidet A shower is sprayed from the tip of the A shower is sprayed from the tip of the nozzle, nozzle, and sprays the more delicate female and washes your posterior. parts. Press the shower button. - Page 24 ■ Posterior massage washing Spray strength is alternated between strong and weak during posterior washing to provide a massaging effect. Press the MASSAGE button during posterior washing. To stop the massage spray, press the MASSAGE button again. * Massage effect varies depending on the washing strength. This is high and low when the washing strength is High and Low respectively.
- Page 25 ■ Drying Warm air will be blown out, and dry the parts which were wet by the shower. Press the DRY button again to Press the DRY button. change the temperature of the warm air. * Deodorizing is stopped temporarily while the drying The warm air temperature setting is arailble function is used.
- Page 26 《How to use convenient functions》 ■ Power save One-Touch Power Save: Controls power consumption by turning off the toilet seat heater for a period of 8 hours overnight or during other extended periods when this product is not being used. The settings automatically revert after 8 hours. One-touch power save (8 hours) Press the POWER SAVE button.
- Page 27 ■ Other convenient functions Seat heater auto-off This product is equipped with a function that prevents low temperature burns by automatically switching the toilet seat heater OFF when it is occupied. Follow the procedure below. ■ Setting and canceling • Press the STOP button and the POWERFUL shower button simultaneously for 2 seconds or longer.
- Page 28 Making the spray strength still milder If the "LO" setting for the shower spray is still too strong, adjust the spray strength using the following procedure. ■ Setting and canceling • Press the BIDET button and the POWER SAVE ON/OFF button simultaneously for 2 seconds or longer.
-
Page 29: Maintaining This Product
Maintaining this product When maintaining this product, WARNING: remove the power plug from the wall outlet. Failure to do so could result in electric hazard or fire. Do not pour water or cleanser in WARNING: the body. Do not splash water or cleanser on the body or on the power plug. - Page 30 How to clean the deodorizing cartridge The deodorizing cartridge may perform poorly if covered with dust. If odors start to bother you, please clean the cartridge. How to clean the deodorizing cartridge 1. Disconnect the power plug from the Underside of the toilet seat outlet.
-
Page 31: Cleaning The Strainer
Cleaning the strainer If the spray strength weakens over time, clean the strainer using the following procedure. Cleaning the strainer 1. Close the water shutoff valve to cut 3. Remove the dirt off the water supply. adhering to the inside of Since the water shutoff valve is adjusted beforehand, the strainer by rinsing it keep the original position (to what extent you turned... - Page 32 Cleaning the hidden portions of the toilet seat lid When cleaning this product, be sure to pull the power plug out of the wall outlet. CAUTION Removing the toilet seat lid 1. Move the pin hole on the right side 2.
-
Page 33: Removing The Body
Cleaning the portions of the toilet that are hidden by the body 1. Removing the body 1. Remove the power plug from the wall 2. Close the water shutoff valve to cut off the water supply. (See caution 2.) outlet. (See caution 1.) S i n c e t h e w a t e r s h u t o ff v a l v e i s a d j u s t e d beforehand, keep the original position (to what extent you turned the valve) in mind. -
Page 34: Assembling The Body
2. Cleaning 3. Assembling the body Wipe out the body using a soft 1. Place the body on the toilet bowl. Align the inverted triangle mark cloth dampened with water. ) on the body locking plate with the protrusion on the rear of the body. - Page 35 Preventing freezing In freezing conditions, the water in this product may freeze and cause damage. If there is danger of water lines freezing, implement the following freeze prevention method to prevent damage. Leave the power plug in the wall outlet. General freeze prevention measures 1.
- Page 36 Thawing frozen water supply If the water in the body water supply hose or in the water supply connection freezes, and the wash or bidet does not spray water, the hose or connection must be thawed. To thaw the hose or connection gradually, increase the air temperature in the room.
- Page 37 Draining this product for periods of extended disuse If this product will not be used for an extended time (such as when you are away on a long trip), use the following procedure to drain the water from of this product. Water left in this product for an extended period can become contaminated and clog this CAUTION: product, or can freeze.
-
Page 38: Replacing Batteries In The Remote Control
Replacing batteries in the remote control As the batteries weaken, the battery lamp will begin to blink. Battery lamp * Usually, this battery lamp turns off. * The batteries provided with this product have been used to check operations during construction, and so may have a useful life shorter than commercially available batteries. -
Page 39: Troubleshooting
Troubleshooting You can easily correct some of the problems with this product. Before requesting repairs, please check the following items. If you are unable to correct the problem using the remedies shown below, contact the store where you purchased this product. All functions Symptom Cause... - Page 40 Posterior cleaning and bidet cleaning (continued) Remedy Symptom Cause Press the water temperature button Water temperature is not set to an and adjust the water temperature to the appropriate temperature. appropriate level. (See page 22.) Spray water is not The wash or bidet function was The water takes about 3 minutes to warm warm.
- Page 41 Others Remedy Symptom Cause The body chatters and Push the body farther back and lock it in deviates from correct The body is not locked. position. (See page 34.) position. The rear feet It is not out of order. (projections from the The rear feet (projections from the rear) rear) do not touch were designed to float.
-
Page 42: After-Sales Service
After-sales service 1. Before Requesting Repairs If this product breaks down, see "Troubleshooting" on page 39. If the trouble is not repaired even after that, contact the store where you purchased this product. Furthermore, even if there is no actual trouble, make inquiry in the following cases. -
Page 43: Specifications
Specifications Type CW-RS3-W Water supply method Direct connection to tap water Tap water pressure range 0.06 to 0.74 MPa (0.6 to 7.5 kgf/cm Maximum rating AC 220 V, 305 W, 50 Hz Product dimensions Width 426 mm x Depth 557.5 mm x Height 162 mm Product weight Approx. - Page 44 Dealer (Store name, Address, Tel.) Website: http://www.lixil.co.jp/ GCW-1220A-W(11040)