Advertisement
WARNING! Wear approved safety eye protection, ear defenders, gauntlets and, if dust is generated, respiratory protection.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Keep hands and body clear of the worktable when operating the saw, and DO NOT position your body in line with the abrasive wheel.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Avoid subjecting disc to excessive strain, always ease disc down against workpiece (a harsh downward impact may break the disc). DO NOT
apply undue force on the handle in order to cut workpiece. Maintain a controlled cutting speed through the workpiece.
DO NOT cover the motor or obstruct ventilation openings.
WARNING! DO NOT switch on the saw whilst the disc is in contact with the workpiece. Bring the rotating disc to the workpiece.
Avoid unintentional starting of the saw.
DO NOT hold the workpiece by hand. Use base vice to secure the workpiece.
DO NOT attempt to cut any material bigger than the maximum capacities stated in section 2: 'Specifications'
DO NOT use the saw for a task it is not designed to perform.
DO NOT allow untrained persons to operate the saw.
DO NOT get the saw wet, or use in damp or wet locations or areas where there is condensation.
WARNING! DO NOT use the saw where there are flammable liquids, solids or gases such as paint solvents and including waste wiping rags etc.
DO NOT operate the saw if any parts are missing or damaged as this may cause failure and/or personal injury.
DO NOT remove the safety guard whilst the saw is in use.
DO NOT attempt to remove a workpiece until the disc has stopped rotating.
DO NOT touch the workpiece close to the cut as it will be very hot. Allow to cool. The cut edge of the workpiece will also be very sharp.
DO NOT leave the saw operating unattended.
DO NOT operate the saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use switch off the saw and remove the plug from the power supply.
To move the saw, lock the swing arm with the lock button and lift by the transportation handle.
2. SPECIFICATIONS
General purpose abrasive saw suitable for site use. Supplied with abrasive disc suitable for metal-cutting.
Motor . . . . . . . . . . . . . . . . . . 2480W - 230V
No-load speed . . . . . . . . . . . . . . . . 3800rpm
Double Insulated . . . . . . . . . . . . . . . Class II
Size of disc . . . . . . . . . . Ø355 x 3 x 25.4mm
Disc Part No. . . . . . . . . . . . . . . . PTC/355C
3. CONTENTS
Unpack the product and check the contents. Ensure that there is no damage. If any problem is noted, contact your supplier immediately.
IMPORTANT: Abrasive disc MUST only be fitted by a qualified person.
fig.2
© Jack Sealey Ltd
Cutting capacity @ 90°(bar) . . . . . . . 105mm
Cutting capacity @ 90°(pipe) . . . . . Ø120mm
Cutting capacity @ 45°(bar) . . . . . . . . 50mm
Cutting capacity @ 45°(pipe) . . . . . . Ø80mm
Mitre angles . . . . . . . . . . . . . . . . . . . 0° - 45°
Fig.1
Original Language Version
Net Weight . . . . . . . . . . . . . . . . . . . . 21.85kg
Extraction Port (ID/OD) . . . . . . 35mm/38mm
Noise Power . . . . . . . . . . . . . . . . . . . . 94dB
Noise Pressure. . . . . . . . . . . . . . . . 107dB.A
Vibration (under load). . . . . . . . . . . 4.39m/s²
fig.3
fig.1
SM355D
Issue:3 (I) - 16/02/16
Advertisement
