Subscribe to Our Youtube Channel
Related Manuals for Phoenix Mecano Dewert Okin DUOMAT 9
Summary of Contents for Phoenix Mecano Dewert Okin DUOMAT 9
- Page 1 DUOMAT 9 Installation Instructions (Translation of the original installation instructions)
-
Page 3: Foreword
DUOMAT 9 Foreword Foreword Document revision history Version Date Modification, change 05/2014 First release 04/2015 Optional: AUX connection po- sitions 01/2016 Cover/shutter, Bowden cable Disclaimer and exclusion of liability DewertOkin is not responsible for damage resulting from: failure to observe these instructions, ... -
Page 4: Notice For Customers In Eu Nations
Foreword DUOMAT 9 Notice for customers in EU nations German Inspection Authority (TÜV SÜD Product Service) testing label The construction of the DUOMAT 9 has been inspected by the German TÜV SÜD Product Service Inspection Authority. TÜV SÜD Product Service also monitors the production of the DUOMAT 9. The official German TÜV SÜD Product Service certifies this construction inspection and production monitoring. -
Page 5: Table Of Contents
DUOMAT 9 Table of contents Table of contents Foreword Document revision history Disclaimer and exclusion of liability Contact address Creation of a complete operating instruction manual for the entire end product Notice for customers in EU nations Table of contents General Information Versions About these installation instructions... - Page 6 Table of contents DUOMAT 9 Maintenance Maintenance Cleaning and care Disposal 10.1 Packaging material 10.2 Drive components 10.3 Batteries Declaration of incorporation/installation EU Declaration of Conformity Additional information 79338 4.0...
-
Page 7: General Information
DUOMAT 9 General Information General Information Versions The DUOMAT 9 can be operated in several different versions (configurations). The DUOMAT 9 name, as used here, also includes the DUOMAT 9+1 and DUOMAT 9+2 configurations. The "Possible combinations" chapter includes information about the different device combinations avail- able. -
Page 8: Conventions Used
General Information DUOMAT 9 Conventions used Notices which do not relate to safety are indicated in these instructions with a triangle: Triangular notice symbol Safety notice explanations WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. -
Page 9: Safety Notices
DUOMAT 9 Safety notices Safety notices Proper and intended usage The DUOMAT 9 is meant to be installed in beds. It provides motor adjustment capabilities for movable reclining bed parts. It should be used in conjunction with suitable fittings and mechanics: ... -
Page 10: Safety Notices Within The Installation Instruction And The Operating Instructions For The Entire Machine
Safety notices DUOMAT 9 The DUOMAT 9 can be used by children of 8 years and older, persons with reduced physical, sen- sory or mental capabilities, or persons with lack of experience or knowledge when they are super- vised or instructed concerning the safe use of the device and when they understand the resulting risks. -
Page 11: Selection And Qualification Of Personnel
DUOMAT 9 Safety notices Selection and qualification of personnel This drive should only be installed into the end product by someone who has completed training in electronic motor assembly or has equivalent qualifications. You should only install this drive when you are qualified to do so. Otherwise, a properly qualified person should be found for this task. -
Page 12: Product Identification
Safety notices DUOMAT 9 Product identification 2.5.1 Ratings plate A ratings plate on each drive specifies the exact name and serial number of the drive. It also states the technical specifications valid for that particular drive. The maximum pushing force is specified here. -
Page 13: Possible Combinations
DUOMAT 9 Possible combinations Possible combinations The DUOMAT 9 can be combined for use with other drives. The following basic combinations are possible: a DUOMAT 9 with a controller keypad, a DUOMAT 9+1 as the main drive and a single drive used as a slave drive with a controller key- pad, ... - Page 14 Possible combinations DUOMAT 9 3.1.1 Optional: AUX connection positions The optional AUX connection label indicates the location of the AUX connection for service and maintenance personnel. Figure 4 Optional AUX connection label on the back of the DUOMAT 9 A DUOMAT 9 B DUOMAT 9 ER/SB (with mechanical reset function) C DUOMAT 9 ER/SB (with mechanical reset...
-
Page 15: Description
DUOMAT 9 Description Description The DUOMAT 9 is an electrically driven unit that is responsible for adjusting the end product. The head and foot sections of a bed can be adjusted depending on the drive options. The drive is oper- ated by means of a controller keypad. - Page 16 Description DUOMAT 9 4.1.1 Configurations variants for the DUOMAT 9 Figure 6 Rear sides of the DUOMAT 9 A DUOMAT 9 B DUOMAT 9 ER/SB (with mechanical reset function) C DUOMAT 9 ER/SB (with mechanical reset function) and Bowden cable retainer CAUTION The mechanical reset function operates without mains power.
- Page 17 DUOMAT 9 Description 4.1.2 Mains power supply connection WARNING Please follow these operating instructions carefully. You could be injured by fire or electrical shock if you do not follow these assembly instructions. The appropriate pluggable power supply cord is included, depending on the regional version (USA, EURO continental Europe, the UK, Australia or Japan).
-
Page 18: Technical Specifications
Technical specifications DUOMAT 9 Technical specifications Mains power supply connection 100 V - 240 V AC, 50/60 Hz (refer to the ratings plate on the drive) 4.0 A – 1.5 A (depending on power connection) Current consumption at rated load Push force Max. - Page 19 DUOMAT 9 Technical specifications Figure 8 Dimensions of the DUOMAT 9 drive, in mm Figure 9 Dimensions of the 9 DUOMAT ER/SB (with mechanical reset function or Bowden cable retainer), in mm 581±2 Figure 10 Dimensions of the DUOMAT 9 drive, in mm 79338 4.0...
- Page 20 Technical specifications DUOMAT 9 Pivot lever Max. 34 Figure 11 Pivot lever, in mm (an example) Only use a pivot lever with the proper dimensions. Make sure that you consider the amount of torque that is generated by the drive when you de- sign the weld between the bracket and the end product.
-
Page 21: Installation
DUOMAT 9 Installation Installation Safety notices to observe during installation Basic safety rules must be followed in order to ensure that the end product can be continually oper- ated in a safe manner. These rules must be observed while using the end product and while in- stalling the drive. -
Page 22: Installation Procedure
Installation DUOMAT 9 Installation procedure 6.2.1 An example installation Before installing the drive, make sure that you are observing all of the safety notices found in the "Safety notices to observe during installation" section. CAUTION For the optional rechargeable battery: Disconnect the cable for the rechargeable bat- tery from its socket before installing the DUOMAT 9. - Page 23 DUOMAT 9 Installation Figure 13 Removing the shutters D Shutters E Fitting mounts F Snap-in locking device (for cover) G Locking tab on shutter lock 4 Lift the locking tab on the shutter lock (F) and slide the shutter lock towards the middle of the drive.
- Page 24 Installation DUOMAT 9 10 Connect all of the additional functionality (optional features such as slave drives, controller key- pad, battery, etc.). (Refer to section 3.1 "Layout of system connections".) 11 Close off the unused sockets using dummy plugs. The dummy plugs ensure that the sockets are properly protected against any splashed water.
- Page 25 DUOMAT 9 Installation After plugging the power plug into the power outlet: NOTICE There is a delay after the supply voltage is applied before the device actually turns on. Wait at least seven seconds before beginning the commissioning. 6.2.2 Option mechanical reset function, with Bowden cable attachment Figure 17 Mounting the drive with mechanical reset function A Bowden cable holder...
- Page 26 Installation DUOMAT 9 Figure 18 Installation of the Bowden cable for the mechanical reset function (optional) 1 Remove the pull-out guard (C). 2 Move the push-out slider (B) in the direction of arrow (as shown in Figure 18.2) to the Bowden cable retainer (A).
- Page 27 DUOMAT 9 Installation 6.2.3 Electrical connection CAUTION Work on electrical components should be conducted only when the mains power con- nection is unplugged. Routing the electrical cables When routing the cables, be sure that: the cables cannot get jammed, ...
- Page 28 Installation DUOMAT 9 6.2.4 Dismantling CAUTION Work on electrical components should be carried out only when the mains power and battery plugs (when present) are unplugged. CAUTION Be sure to carry out work on the drive in a position so that no loads are bearing on it. Only in this way can you be sure to avoid any risks of crushing or injury.
-
Page 29: Operating Notes
DUOMAT 9 Operating notes Operating notes The factual information contained within may be used when you are creating the end-product man- ual. The installation instructions do not contain all information required for the safe operation of the end product. They only describe the installation and operation of the drive as a partially assembled piece of machinery. - Page 30 Operating notes DUOMAT 9 Optional: Mechanical reset functions (Bowden cable and rotary switch) Figure 19 Mechanical reset function at the rear of the DUOMAT 9 A Sticker label for the mechanical reset func- B Attachment for the Bowden cable tion C Mechanical reset function (rotary switch) D Normal mode position E Symbol: Lower the foot section...
- Page 31 DUOMAT 9 Operating notes Optional: Mechanical reset function (rotary switch for head and foot sections) Figure 20 Mechanical reset function at the rear of the DUOMAT 9 Switch position Function Lowering head section Lowering foot section Lowering head and foot sections Normal mode 79338 4.0...
- Page 32 Operating notes DUOMAT 9 Optional: Mechanical reset function (rotary switch for head section) Figure 21 Mechanical reset function at the rear of the DUOMAT 9 Switch position Function Lowering head section Normal mode The DUOMAT 9 (with adjustable head section) features only the "Normal mode" (B) and "Lower head section"...
- Page 33 DUOMAT 9 Operating notes If you have purchased the DUOMAT 9 with the mechanical reset function (rotary switch or Bowden cable), then you should note the following: In the event of a power failure or emergency, the head and foot sections can be lowered me- chanically using the mechanical reset function.
-
Page 34: Troubleshooting
Troubleshooting DUOMAT 9 Troubleshooting This chapter describes troubleshooting methods for fixing problems. If you experience an error that is not listed in this table, please contact your supplier. CAUTION Only qualified specialists who have received electrician training should carry out trou- bleshooting and repairs. -
Page 35: Maintenance
DUOMAT 9 Maintenance Maintenance You should only use spare parts which have been manufactured or approved by DewertOkin. Only these parts will guarantee a sufficient level of safety. Maintenance Type of check Explanation Time interval Check the function and A qualified electrician should carry Periodic inspections can safety of the electrical sys-... -
Page 36: Cleaning And Care
Maintenance DUOMAT 9 Cleaning and care The DUOMAT 9 was designed so that it is easy to clean. Its smooth surfaces simplify the cleaning process. NOTICE Never clean the drive in an automated washing system or with a high-pressure cleaner. Do not allow fluids to penetrate the drive. -
Page 37: 10. Disposal
DUOMAT 9 Disposal 10. Disposal 10.1 Packaging material The packaging material should be sorted into recyclable components and then disposed of in ac- cordance with the appropriate national environmental regulations (in Germany according to the re- cycling law KrWG from 01.06.2012; internationally according to the EU Directive 2008/98/EC (Waste Framework Directive WFD as of 12.12.2008)). -
Page 38: Declaration Of Incorporation/Installation
Declaration of Incorporation According to Appendix II of the EU Machinery Directive 2006/42/EC The manufacturer: DewertOkin GmbH Weststraße 1 32278 Kirchlengern Germany declares that the incomplete machine described below DUOMAT 9, DUOMAT 9 CARE, DUOMAT 9 HOSP DUOMAT 9+1, DUOMAT 9+1 CARE, DUOMAT 9+1 HOSP DUOMAT 9+2, DUOMAT 9+2 CARE, DUOMAT 9+2 HOSP complies with the following basic requirements of the Machinery Directive (2006/42/EC): Sections:... -
Page 39: Eu Declaration Of Conformity
EU Declaration of Conformity In compliance with Appendix IV of the EU Directive 2014/30/EU In compliance with Appendix IV of the EU Directive 2014/35/EU In compliance with Appendix VI of the EU Directive 2011/65/EU The manufacturer: DewertOkin GmbH Weststraße 1 32278 Kirchlengern Germany declares that the following product... -
Page 40: Additional Information
Additional information In accordance with EN 60601-1, "Electrical medicinal devices", the following standards are used : EN60601-1, Section 4 General requirements EN60601-1, Section 6 Classification Labelling – general EN60601-1, Section 7.1 Labelling – inscriptions EN60601-1, Section 7.2 EN60601-1, Section 8 Protection against electrical danger EN60601-1, Section 11.1 Overheating protection... - Page 41 In accordance with EN 60601-2-52:2010, "Particular requirements for the safety and essential per- formance of medical beds", the following standards have been used: EN 60601-2-52, Section 201.6.2 Protection against electrical shock: Protection class EN 60601-2-52, Section 201.6.3 Control panel symbols (depending on model, cus- tomer requirements) EN 60601-2-52, Section 201.9.2.2.5 Controller with independent reset function (e.g.
- Page 44 DewertOkin GmbH Weststrasse 1 Kirchlengern 32278, Germany Tel: +49 5223/979-0 Fax.: +49 5223/75182 http://www.dewertokin.de Info@dewertokin.de ID No.: 79338...
Need help?
Do you have a question about the Dewert Okin DUOMAT 9 and is the answer not in the manual?
Questions and answers