Advertisement
2. Installation of the Lavatory :-
WALL-MOUNT INSTALLATION (K-2018IN-1WH*)
1. Drill two
14mm Anchor holes, 76 mm deep
Ø
into the wall according to the Rough-in diagram.
2. Insert the plastic anchors (provided) in two
holes.
3. Insert the metal studs (provided) into these
plastic anchors using an adjustable wrench.
4. Ensure that at least 70 mm (approx.) of each
stud should remain exposed from the wall.
Refer Fig. #3
5. Install the faucet & drain to the lavatory
according to the manufacturer's instructions.
NOTE :- Do not fully tighten slip-joint drain
connections at this time.
Refer Fig. #4
FULL-PEDESTAL INSTALLATION (K-2017IN-1*)
1. Apply self-adhesive leveling pads (provided)
to each of the three ridges in the bottom recess of the
lavatory.
Refer Fig. #7
2. Mark the centerline on the floor with a pencil & position
the pedestal on the floor centerline location.
Refer to the roughing-in dimensions for correct
placement.
3. Carefully set the lavatory on the pedestal & move the
pedestal as required to ensure proper fit in the desired
location.
NOTE :-The lavatory must be supported by the
pedestal.
4. Mark the center of each anchoring hole on the wall.
5. Carefully remove the lavatory from the pedestal. Then
move the pedestal from the area.
Refer Fig. #8
6. Drill two 14mm Anchor holes,
Ø
wall at the marked location.
7. Insert the plastic anchors in two holes.
8. Insert the metal studs (provided) into these plastic
anchors using an adjustable wrench.
9. Ensure that at least 70 mm (approx.) of each stud
should remain exposed from the wall.
Refer Fig. #9
10.Install the faucet & drain to the lavatory according
to the manufacturer's instructions.
HALF-PEDESTAL INSTALLATION (K-11341IN-1*)
1. Apply self-adhesive leveling pads (provided) to each of
the three ridges in the bottom recess of the lavatory.
Refer Fig. #14
2. Mark the centerline on the wall with a pencil.
3. Mark the location of the mounting holes of the lavatory
according to the Roughing-In diagram.
4. Drill two Ø14mm Anchor holes, 76 mm deep into the
wall at the marked location.
5. Insert the plastic anchors in two holes.
6. Insert the metal studs (provided) into these plastic
anchors using an adjustable wrench.
7. Ensure that at least 70 mm (approx.) of each stud
should remain exposed from the wall
Refer Fig. #16.
8. Install the faucet & drain to the lavatory according
to the manufacturer's instructions
NOTE :- Do not fully tighten slip-joint drain connections
at this time.
Refer Fig. #17
9. Place the Lavatory onto metal studs and install
the washer and nut, Do not fully tighten the nuts
at this time for pedestal adjustment.
Refer Fig. #18
* Installation doesn't allow use of any tool other than standard wrench. For this reason, split turns have been mentioned rather than full turns.
SERVICE PARTS
(Supplied with the Product)
A. Hardware Kit 1213117
B. Levelling Pads 63069
Important Notice for Care, Cleaning & Daily use
To keep your lavatory looking new, make sure you rinse it out thoroughly after each use.
DO NOT USE ABRASIVES on this product, as they will scratch & ruin the surface.
Stubborn stains, paint, or tar can be removed with turpentine or paint thinner.
1232255-IN01-A
3
Metal Studs
4
7
8
Center of
Anchoring Holes
9
76 mm deep into the
14
15
16
Metal Studs
17
6.
Carefully place the lavatory against the wall,
so the metal studs extend through the
lavatory holes.
7. Level the lavatory.
8. Install the plastic washer & nut (provided)
& tighten suitably.
CAUTION : Risk of product damage.
Do not over tighten the nut. Over tightening
may cause damage to the product.
*
Use wrench to tighten 8-10 N-m/ 6-9 turns.
Plastic Anchors
(1 turn = 45°) past finger tight.
Refer Fig. #5
9. Connect & tighten the bottle trap as per
manufacturer's instructions. Connect the
hot & cold water supplies to the faucet.
10.Evenly p
ut the sealant around the mounting
surface of the lavatory touching the wall.
Refer Fig. #6
11.Clean the lavatory top.
NOTE :- Do not fully tighten slip-joint drain
connections at this time.
Refer Fig. #10
11.
Carefully place the lavatory against the wall,so the
metal studs extend through the lavatory holes.
Install the washer and nut, Do not fully tighten the
nuts at this time for pedestal adjustment.
Refer Fig. #11
12. Connect & tighten the trap as per manufacturer's
instructions. Connect the hot & cold water
supplies to the faucet.
Pedestal
13. Place the Pedestal with proper adjustment & level
the lavatory .Use additional self-adhesive leveling
pads as required to level the lavatory. Tighten the
Mark center
line Here
nuts suitably.
CAUTION : Risk of product damage.
Do not over tighten the nut. Over tightening
may cause damage to the product.
*
Use wrench to tighten 8-10 N-m/ 6-9 turns.
(1 turn = 45°) past finger tight.
Refer Fig. #12
14. Evenly put the sealant around the mounting
surface of the lavatory touching the wall.
Refer Fig. #13
Plastic
Anchors
15. Clean the lavatory top.
Metal Studs
10.Connect & tighten the trap as per manufacturer's
instructions. Connect the hot & cold water
supplies to the faucet.
11. Place the Half-Pedestal beneath the lavatory
& mark the location of mounting holes of Pedestal.
12. Install the Half-Pedestal with suitable hard wares.
13. Level the lavatory .Use additional self-adhesive
leveling pads as required to level the lavatory.
14. Tighten the lavatory nuts properly to complete the
installation.
CAUTION : Risk of product damage.
Do not over tighten the nut. Over tightening
Mark center
Line Here
may cause damage to the product.
*
Use wrench to tighten 8-10 N-m/ 6-9 turns.
(1 turn = 45°) past finger tight.
Refer Fig. #19
15. Evenly put the sealant around the mounting
surface of the lavatory touching the wall.
16. Clean the lavatory top.
Refer Fig. #20
Plastic Anchors
-2-
5
Metal Studs
Lavatory
Nut
Plastic Washer
45°
6-9 turns (45
° each
) allowed past finger tight
6
10
11
Metal Studs
Nut
Plastic Washer
12
Lavatory
Center line
Pedestal
45°
6-9 turns (45
° each
) allowed past finger tight
13
18
Metal Studs
Nut
Plastic Washer
19
Lavatory
Center line
Pedestal
45°
6-9 turns (45
° each
) allowed past finger tight
20
Toll Free 1800 103 2244
in
Advertisement
