Advertisement
3. Press STATUS to check the current arming level.
4. Select Direct and Indirect to bypass sensors.
5. Press and hold each panic button until the red/green
indicator light stops flashing and the appropriate
alarm sounds.
6. Turn lights on or off (see system owner's manual).
7. Press and hold the buttons marked
time to mute the touchpad. Continue to hold the but-
tons until you hear a series of confirmation beeps.
8. Press various buttons to test the mute feature.
9. Press and hold the buttons marked
time to turn off the mute function. Continue to hold
the buttons until you hear a series of confirmation
beeps.
10.Contact the central monitoring station after you have
finished testing the touchpad.
Mounting the Touchpad
Test the wireless touchpad at a desired location. Ensure
that a clear RF signal exists between the touchpad and
control panel. After successfully testing for a clear RF
signal, you can mount the touchpad as follows:
1. Secure the touchpad mounting bracket to a desired
surface. Use the screws from the accessory pack to
mount the bracket (see Figure 3).
Mounting
Screws
Holes
Figure 3. Securing the Mounting Bracket.
2. Attach the touchpad to the mounting bracket by plac-
ing the touchpad bottom into the bracket bottom.
Press the touchpad into place to ensure a secure fit
(see Figure 4).
)
@ÃTrpˆ…v‡’
‹!#ÃB@ÃTrpˆ…v‡’Ã8‚p‚…qÃhqÃ8‚p‚…qÃ@‘ƒ…r††Ãh…rÇ…hqr€h…x†Ã‚sÃB@ÃTrpˆ…v‡’Ã6q‰r‡Ãv†ÃhÃ…rtv†
‡r…rqÇ…hqr€h…xÂsÃB@ÃTrpˆ…v‡’Ã6yy‡ur…Ç…hqr€h…x†Ãh…rÃ…‚ƒr…‡vr†Ã‚sÇurv…Âr…†
6yyÃ…vtu‡†Ã…r†r…‰rq
1
2
and
at the same
1
2
and
at the same
2
466-1012 Rev. D
Figure 4. Attaching Touchpad to Mounting Bracket
Specifications
Model No: 60-597
RF Frequency: 319.5 MHz
Compatibility: Concord, Concord Express, and Advent security
panels
Power Requirements: One 3.0 V DC lithium battery
Battery Life: 5 to 8 years
Storage Temperature: -40° to 140°F (-34° to 60°C)
Operating Temperature: 10° to 120°F (-12° to 49°C)
Maximum Humidity: 90% relative humidity, non-condensing
Dimensions: 2.1 x 0.86 x 6.1 in. (5.33 x 2.18 x 15.5 cm)
Notice
This device complies with FCC Rules Part 15. Operation is sub-
ject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by GE Secu-
rity can void the user's authority to operate the equipment.
FCC ID No.: B4Z-861-HTTP
!&$ÃSrqÃA‚‘ÃS‚hqÃ
6…qrÃCvyy†ÃHIÃ$$ !Ã
UrpuvphyÃTˆƒƒ‚…‡)Ã'&&&!%!#
Printed in Mexico
Advertisement
