Handling The Equipment; Instructions For Assembly; List Of Spare Parts - Kettler COACH Assembly Instructions Manual

GB
Assembly Instructions

Handling the equipment

Before using the equipment for exercise, check carefully to en-
■
sure that it has been correctly assembled.
In choosing the location of the apparatus, ensure a sufficient
■
safety distance from any obstacles. The apparatus must not be
mounted in the immediate vicinity of main passageways (paths,
doorways, corridors).
It is not recommended to use or store the apparatus in a damp
■
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
The rowing machine must be set up on an even impact-resistant
■
base. To absorb the vibrations, lay a straw or rubber mat under
the machine.
The product is designed for use by adults and children should
■
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the man-
ufacturer cannot be held liable. If, in spite of this, children are

Instructions for Assembly

Ensure that you have received all the parts required (see check
■
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
■
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
Please note that there is always a danger of injury when work-
■
ing with tools or doing manual work. Therefore please be care-
ful when assembling this machine.
Ensure that your working area is free of possible sources of dan-
■
ger, for example don't leave any tools lying around. Always dis-
pose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children play
with plastic bags!
The equipment must be assembled with due care by an adult
■
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
The fastening material required for each assembly step is shown
■
List of spare parts page 17 – 19
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the pro-
duct (see spare parts drawing).
Example order: Art. no. 07985-600 / spare-part no. 10100016
/ 2 pieces / S/N......
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
4
allowed to use the equipment, ensure that they are instructed in
its proper use and supervised accordingly.
A slight production of noise at the bearing of the centrifugal
■
mass is due to the construction and has no negative effect upon
operation.
The rowing machine has a brake system, which requires little
■
maintenance and does not require any adjusting work.
Do not use corrosive or abrasive materials to clean the equip-
■
ment. Ensure that such materials are not allowed to pollute the
environment.
To operate correctly, the pulse function requires a minimum volt-
■
age of 2,7 volts.
Please ensure that liquids or perspiration never enter the ma-
■
chine or the electronics.
Before use, always check all screws and plug-in connections as
■
well as respective safety devices fit correctly.
in the diagram inset. Use the fastening material exactly as in-
structed. The required tools are supplied with the equipment.
Bolt all the parts together loosely at first, and check that they
■
have been assembled correctly. Tighten the locknuts by hand un-
til resistance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
For technical reasons, we reserve the right to carry out prelimi-
■
nary assembly work (e.g. addition of tubing plugs).
Please, use suitable supporting material (such as packing
material, polystyrene or similar material) for this assembly
step in order to avoid a scratching or damaging of the hou-
sing.
should be clearly stated on the order by adding the words „with
fastening material".
KETTLER GB Ltd. · KETTLER House, Merse Road · North
GB
Moons Moat · Redditch, Worcestershire B98 9HL
KETTLER International Inc. · P.O. Box 2747 · Virginia Beach,
USA
VA 23450-2747
http://www.kettler.net