Related Manuals for Sony HKSR-9003
Summary of Contents for Sony HKSR-9003
- Page 1 RGB 4:4:4 PROCESSOR BOARD HKSR-9003 INSTALLATION MANUAL 1st Edition...
- Page 2 ! 警告 このマニュアルは，サービス専用です。 お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災， 人身事故につながることがあります。 危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。 設置や保守， 点検， 修理などを行う前に， カムコーダー本体に付属している下記マニュアルの「安 全のために」を必ずお読みください。 . SRW-9000 メンテナンスマニュアルおよびオペレーションマニュアル ! WARNING This manual is intended for qualifi ed service personnel only. To reduce the risk of electric shock, fi re or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualifi...
-
Page 3: Section 1 Installation
This manual describes information on the maintenance and component-based service of the unit. Installation of HKSR-9003 If you need this manual, please contact your local Sony Sales Offi ce/Service Center. Attach and adjust the unit properly following the proce- dures in Section 1-3 and later. -
Page 4: Installation Procedures
6. Detach the board spacer. 7. Disconnect the harness (AXM-VPR) from the connector CN3 on the AXM-37 board. Board spacer Board retainer PSW2.6 x 5 Slits Harness (AXM-VPR) PSW2.6 x 5 1-2 (E) HKSR-9003... - Page 5 Example) To remove the SS-103 board Remove the VPR, RE, and SS boards in this order. The VDA-69 board need not be removed. VDA-69 board VPR-101 board RE-244 board SS-103 board Board name Number of board removing order 1-3 (E) HKSR-9003...
- Page 6 TR-139 board using the cable stopper CN1010 Blue (BNC). (Refer to Section 1-4-2.) CN1012 16. Remove the VPR-101 board from the unit. Gray Be very careful so that the harnesses and cables are not caught. 1-4 (E) HKSR-9003...
- Page 7 20. Connect the connector CN100 on the PR-318 board to the connector CN2201 on the VPR-101 board. IC1202 IC1003 21. Install the heatsink (PR) assembly with the Radiation sheet (9 x 12) IC1001 supplied three screws. IC1200 PR-318 board IC1000 CN100 CN2201 VPR-101 board 1-5 (E) HKSR-9003...
- Page 8 25. Hook portion A (three locations) of the cable stopper (BNC-2) to the edge of the heatsink (TR) assembly, and secure the cable stopper with a screw with stopper. Coaxial cable TR-139 board Screw with stopper Cable stopper (BNC-2) 1-6 (E) HKSR-9003...
- Page 9 (30P) with a screw with stopper. CN2101 Cable stopper (BNC) Pushing direction (B) Fine-wire coaxial cable Do not put on the connector. Cable stopper Cable stopper (BNC) (BNC) Arrow B view Arrow B view 1-7 (E) HKSR-9003...
- Page 10 fi gure. 36. Install the removed parts by reversing steps 1 Cable stopper (BNC) to 7. 37. Check that the HKSR-9003 has been recog- nized with the SYSTEM menu. (Refer to Sec- tion 1-5.) Harness (AXM-VPR)
- Page 11 Guide Mating connector specifi ed in Figure 1. Connect surface Insert the connector carefully so that the Figure 1 connector guides are not caught by the edge of the mating connector. 5° or less 2° or less 1-9 (E) HKSR-9003...
-
Page 12: Coaxial Cable
Do not pull the cable. Connection Hold the plug to connect. 1. Hold the plug of the coaxial cable. 2. Push the plug perpendicularly to the connec- tor while slightly turning the plug clockwise and counterclockwise. Connecting connector 1-10 (E) HKSR-9003... - Page 13 System Setup Others Option is Installed.” appears on the “Option List” FORMAT SOFT VERSION window. TEST SG HOURS METER FORMAT LIST KEY MAP OPTION LIST KEY INHI SERVO REC INHI BATTERY Option List OTHERS No Option is Installed. 1-11 (E) HKSR-9003...
- Page 15 ことを禁止します。 The material contained in this manual consists of The material contained in this manual consists of information that is the property of Sony Corporation. information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication Sony Corporation expressly prohibits the duplication...
- Page 16 Printed in Japan Sony Corporation HKSR-9003 (SY) J, E 2009. 9 08 4-160-066-01 ©2009...