Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Barco ISIS LFC
Summary of Contents for Barco ISIS LFC
- Page 1 ISIS LFC Installation Guide...
- Page 2 2 ______________________________________________________________ Barco – ISIS LFC – Installation Guide...
-
Page 3: Table Of Contents
LFC calibration..................20 Important Notices The material in this guide consists of information that is the property of Barco and is intended only for use by the purchasers of the type of product described in this guide. The product contains material in which Barco retains proprietary rights. Any act involving software reproduction or intervention is prohibited. -
Page 4: Introduction
‘LCD Flicker’, can cause eye-fatigue and affect the interpretation of the displayed data. With the ISIS LFC kit here described, a unique set of algorithms is integrated in the ISIS display that reside in the hardware interface of the display (between the graphics generator and the LCD). - Page 5 Figure 1-2 ISIS before and after LFC kit installation Barco – ISIS LFC – Installation Guide ______________________________________________________________ 5...
-
Page 6: Installation
2. Installation Introduction In this section is described how to install an ISIS LFC kit into an ISIS type Main Display Panel. The installation must be performed by qualified personnel only. 2.1.1 Parts list and figures Kit number: K5830195 Kit description: UN LFC INTEGRATION KIT ISIS Part nr. - Page 7 Figure 2-2 Wire ties and screws A new warranty label is added for attachment by a qualified person after installation according to the installation procedure described herewith. Barco – ISIS LFC – Installation Guide ______________________________________________________________ 7...
-
Page 8: Introduction
1 Slotted 4.5 mm or 3/16" screwdriver. 1 Phillips #1 screwdriver. 1 Opti-sense (V5660792) for calibration 1 Barco Keypad Firmware Download Tool and KP/Upload cable Z3498894 or equivalent (ref. description of LFC install). 8 ______________________________________________________________ Barco – ISIS LFC – Installation Guide... -
Page 9: Removal Of The Rear Cover
Cover beside the backplane of the LCD. • To completely disconnect the Rear Cover when needed, disconnect the PIB (Panel Interface Board) connector J7 from the Fan Module. Figure 2-4 MDP 471 Rear Cover removal Barco – ISIS LFC – Installation Guide ______________________________________________________________ 9... -
Page 10: Installation Of Modules And Cables
On the PIB (K5830011), replace the µprocessor board (K5830020) by a µprocessor board (K5830021) and fix this with 2 screws B361085. Lock 2 the screws with a threadlocker, by preference Loctite 242 (Barco ref. V395121), and a tamperproofing coating, by preference Loctite 7400 Varnistop (Barco ref. - Page 11 CN1 on the panel control circuit and J5 on the JANUS Board K5831010. Connect a cable K3494134 between CN2 on the panel control circuit and J4 on the JANUS Board K5831010. Figure 2-7 Panel CN1 and CN2 connection Barco – ISIS LFC – Installation Guide _____________________________________________________________ 11...
- Page 12 Use 10 new screws K58110062 for screwing the fixations named “C”. Fix the 4 backlight covers with the 8 captive screws named “B”. If done by qualified personnel and according to this installation procedure, a new warranty label can be attached. 12 _____________________________________________________________ Barco – ISIS LFC – Installation Guide...
- Page 13 LFC Board support plate Figure 2-9 PIB connection Wire tie V348000 Figure 2-10 Cable fixation Barco – ISIS LFC – Installation Guide _____________________________________________________________ 13...
-
Page 14: Start-Up And Use
OSD menus. The keypad menu looks like this: Input Submenu InputSel:AUTO T LFC:Disable LFC advanced..E > Input Priority < High :Board 2T Medium:Board 1T :Board 3T> No Sync Check < Board 1:Off Board 2:Off Board 3:Off 14 _____________________________________________________________ Barco – ISIS LFC – Installation Guide... - Page 15 The last page controls the upload of the LFC calibration software via the serial port of the ISIS. see Start Starts/stops the upload The progress is indicated on the page See “LFC calibration software upload” for more details. Barco – ISIS LFC – Installation Guide _____________________________________________________________ 15...
- Page 16 Only pins 2, 3 and 5 are used. Pin 2 and 3 are twisted. PC (SUBD9 – Male) ISIS (SUBD9 – Female) 2. Install and start on the PC the “Firmware Download Tool” and select “Barco protocol”. Click “Next”. 16 _____________________________________________________________ Barco – ISIS LFC – Installation Guide...
- Page 17 3. Select the COM-port connected to the ISIS REMOTE IN (J11) PIB connector and click “Next”. 4. The software automatically tries to detect a Barco Protocol device – “Searching for BP device...” is displayed in the terminal window. This takes a couple of seconds.
- Page 18 The terminal returns the command send and the answer from the ISIS display: …“VE …Received data: V2.08” Remark: Barco protocol commands are case sensitive: e.g. if the command “ve” instead of “VE” is sent, the display responds with: “ve Error code 1 : invalid command”...
- Page 19 A Fault will be generated (and indicated) when the Janus board was not detected. • A Warning will be generated (and indicated) when the flash does not contain valid LFC calibration data. Barco – ISIS LFC – Installation Guide _____________________________________________________________ 19...
-
Page 20: Lfc Calibration
2.2.3 LFC calibration 2.2.3.1 Connections Connect a Barco Keypad to connector J10, labelled “KEYPAD”, on the rear side of the display. Place the Optical Sensor on the front of the display and connect it to connector J40, labelled “OPTICAL SENSOR” on the rear side of the display. - Page 21 Failure occurs during step 2, the test measurement fails. This could happen when the optical sensor is not placed on the front of the display or is not connected to the back. Barco – ISIS LFC – Installation Guide _____________________________________________________________ 21...
- Page 22 Note: The warning at the bottom “Not calibrating on input signal!” is shown when no input signal is active during calibration. The calibration should be done with an active input signal connected to the display. 22 _____________________________________________________________ Barco – ISIS LFC – Installation Guide...
- Page 23 Barco – ISIS LFC – Installation Guide _____________________________________________________________ 23...
-
Page 24: Barco, September
28207 Bremen, Germany Phone: +49-421-20 12 20 FAX: +49-421-20 12 29 99 BarcoView, LLC 3059 Premiere Parkway Duluth, Georgia, 30097-4905, USA K5960011-00 ISIS LFC Installation Guide Phone: +1 678 475 8000 Barco, September 2007 Fax: +1 678 475 8100 ©...
Need help?
Do you have a question about the ISIS LFC and is the answer not in the manual?
Questions and answers