Subscribe to Our Youtube Channel
Related Manuals for BOXLIGHT ProColor 3 Series
Summary of Contents for BOXLIGHT ProColor 3 Series
- Page 1 USER GUIDE ProColor Series 3 interactive flat panel Note The pictures in this manual are for reference only and subject to our available products.
-
Page 2: Table Of Contents
Contents Safety Warning ........................1 FCC Statement ........................3 FCC Warning ........................3 Control Panel ........................4 Connection and Setting ...................... 9 Menu Operation ....................... 12 Simple Troubleshooting ....................18 Maintenance ........................20... -
Page 3: Safety Warning
Humidity Do not expose the unit to rain or place in an area of high humidity. Please make sure the indoor environment is dry and cool. Normal operating humidity is 10%~90%RH. BOXLIGHT.COM... - Page 4 There are vents on back cover—please do not use any liquid or spray directly during cleaning. Power Switch Status Signs I means power on, O means power off. Notes for Maintenance This machine can only be maintained by a certified engineer. BOXLIGHT.COM...
-
Page 5: Fcc Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. BOXLIGHT.COM... -
Page 6: Control Panel
Area for placing the absorptive magnetic pen Tap to enter energy-saving mode. Press for at least 2 seconds to enter standby mode. Remote control Receive the remote signal signal receiver USB interface of Android system Bottom loudspeaker Amplify audio 2. Terminal Interface BOXLIGHT.COM... - Page 7 HDMI output interface (personal computer with HDMI output, set-top box, or another video device) AC IN AC power input to connect AC power supply AC SWITCH Open or shut down AC power supply. I means power on, O means power off BOXLIGHT.COM...
- Page 8 Control Panel 3. Remote Control 1) Remote Control Button Instruction BOXLIGHT.COM...
- Page 9 Return to the last operating interface PgUp Page up PgDn Page down Change the channel up/down CH.+/CH.- VOL+/VOL- Increase/reduce the volume F1-F12 PC's F1 through F12 function keys NOTE: Computer-related function keys are not available without a built-in computer. BOXLIGHT.COM...
- Page 10 30 degrees left and right from the remote- control receiver. In order to protect the environment, please dispose used batteries into a recycling box. If the battery is replaced with an incorrect type, it may cause an explosion. BOXLIGHT.COM...
-
Page 11: Connection And Setting
For external computer input, the equipment's best resolution is 3,840x2,160. Recommended computer configuration: 1GB available hard drive 2.0GHz processor, 1GB memory More than 256 color display cards VGA OUT / HDMI OUT, Audio-OUT, USB interface Support resolution 800x600,1,024x768,1,920x1,080, and 3,840x2,160 BOXLIGHT.COM... - Page 12 4. RS232 Connection After using a serial port cable to connect the central control equipment and machine, certain functions of the machine can be controlled via central control equipment, such as machine on/off, adjustment of sound volume, etc. 5. LAN Connection BOXLIGHT.COM...
- Page 13 Connection and Setting 6. USB Connection BOXLIGHT.COM...
-
Page 14: Menu Operation
Use the middle point position on the bottom of the display screen as a starting point. Using a touch pen, drag toward the screen center position to call up the touch menu as shown below. Note: The "Touch A Method" mentioned in this manual to call up the touch menu is shown above. BOXLIGHT.COM... - Page 15 Press the return key on the remote control or click the blank area outside the menu with a touch pen to exit the menu. Note: PC channel will only display when the equipment connects to the built-in computer. BOXLIGHT.COM...
- Page 16 Press Mute on the remote control or directly click with a touch pen to open or close the mute state. Press Back on the remote control or click blank area outside menu with a touch pen to exit the menu. BOXLIGHT.COM...
- Page 17 Press Enter on the remote control or directly click with a touch pen to enter the selected mode. Press Back on the remote control or click blank area outside the menu with a touch pen to exit the menu. BOXLIGHT.COM...
- Page 18 Press Enter on remote control to enter adjustment mode, and press button or directly click with a touch pen to adjust each option. Press Enter/Back to exit the adjustment. Press Back on the remote control or click blank area outside menu with a touch pen to exit the menu. BOXLIGHT.COM...
- Page 19 Press Enter/Back to exit the adjustment. You can also click the Auto icon to adjust automatically. Press Back on the remote control or click the blank area outside the menu with a touch pen to exit the menu. BOXLIGHT.COM...
-
Page 20: Simple Troubleshooting
Check whether the touch pen is facing the screen. not correct Video Function Won't Work Normally No picture and no Check whether the machine is in started state. sound Check whether the signal wire is plugged in properly and whether the input is corresponding to it correctly. BOXLIGHT.COM... - Page 21 Adjust the sound balance in the menu. has sound Check whether the computer sound control panel only sets up one sound channel. Check whether the audio line is connected correctly. HDMI output without Check whether the external device is connected. sound BOXLIGHT.COM...
-
Page 22: Maintenance
No Use of Machine for a Long Period If the machine has not been used for a long period—such as a holiday—please make sure to unplug the power cable to prevent any possible dangers caused by power supply ripple from lightning. BOXLIGHT.COM...
Need help?
Do you have a question about the ProColor 3 Series and is the answer not in the manual?
Questions and answers