Related Manuals for SHANY AHD 22 Series
Summary of Contents for SHANY AHD 22 Series
- Page 1 AHD 22series OSD Manual Thanks for purchasing our product. Before operating the unit, please read the instructions carefully and keep this manual for future reference.
- Page 2 Safety Warning 1. Read this manual carefully before installing the unit Please read this manual first for correct installation and operation. 2. Never install the camera on a ceiling that cannot hold its weight The product may fall down and cause damages. 3.
-
Page 3: Table Of Contents
Table of Contents 1. OSD OPERATION ..................1 1.1 OSD C ................1 ONTROL UTTONS 2. CAMERA OSD ..................... 2 2.1 MAIN MENU....................4 2.2 LENS ......................5 2.3 EXPOSURE ....................6 2.4 BACKLIGHT ....................8 2.5 WHITE BAL ....................10 2.6 DAY&NIGHT .................... -
Page 4: Osd Operation
1. OSD Operation 1.1 OSD Control Buttons Please note the control buttons vary depending on models. They might be at side or back of the camera. For dome type, either you need to open the case to find them or they are simply not available to the camera ①... -
Page 5: Camera Osd
2. Camera OSD To operate the camera OSD setting, use the control key pad to control it. For some models, you might need to open the control panel case to access the control key panel. Press the Enter button which in the center of the control panel to bring up the "MAIN MENU" on the TV/Monitor screen as below. - Page 6 DEFAULT <┘ RETURN SAVE&END<┘, RET<┘ ■ BACKLIGHT HSBLC Settings SELECT AREA1/2/3/4 DISPLAY OFF, ON<┘ BLACK MASK ON, OFF LEVEL MODE ALL DAY, NIGHT<┘ DEFAULT <┘ RETURN SAVE&END<┘, RET<┘ ■ DAY&NIGHT Settings BURST OFF, ON IR SMART OFF, ON<┘ RETURN SAVE&END<┘, RET<┘ ■...
-
Page 7: Main Menu
2.1 MAIN MENU In the "MAIN MENU" of camera OSD, there are several sub-menus and items can be selected to modify the settings. ■ LENS: To select the lens is on DC or on MANUAL mode. ■ EXPOSURE: This is a sub-menu for exposure setting. Please check the details in its section. ■... -
Page 8: Lens
2.2 LENS In "LENS" section, there are MANUAL and DC modes selectable. Descriptions and screenshots below mainly focus on DC mode. ■ MODE: To adjust the lens mode: there are indoor and outdoor modes selectable as show above. The housing of models decides the default mode here. ■... -
Page 9: Exposure
2.3 EXPOSURE In the “EXPOSURE” of camera OSD, there are some items can be selected to modify the settings. The main function of this page is about the optical settings. ■ SHUTTER: To adjust the value of shutter speed and time: AUTO, 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000, 1/10000, 1/50000, x2, x4, x6, x8, x10, x15, x20, x25, x30. - Page 10 ■ DEFOG: To enable or disable DEFOG function: OFF/AUTO available. Selecting “AUTO” can further adjust the advanced settings such as POS/SIZE of DEFOG as shown below. NOTE: To enable DEFOG function, please turn off the D-WDR accordingly. ■ RETURN: Select RET to go back to the previous page; or select SAVE&END to save the settings and then exit OSD.
-
Page 11: Backlight
2.4 BACKLIGHT In the “BACKLIGHT” of camera OSD, BLC and HSBLC modes can be selected to modify the settings. The main function of this page is about the optical settings. ■ LEVEL: To adjust the level of BLC: MIDDLE/LOW/HIGH selectable. ■... - Page 12 ■ BLACK MASK: To enable or disable the Black Mask of the area applying HSBLC function. ■ LEVEL: To adjust the value of HSBLC function. ■ MODE: To select the mode applying HSBLC function: ALL DAY/NIGHT available. Selecting “NIGHT” mode can further adjust the AGC level as shown below. ■...
-
Page 13: White Bal
2.5 WHITE BAL In the “WHITE BAL” section, descriptions and screenshots below will focus on the MANUAL WB mode accordingly. ■ BLUE: To adjust the value of BLUE of Manual WB. ■ RED: To adjust the value of RED of Manual WB. ■... -
Page 14: Day&Night
2.6 DAY&NIGHT In the “DAY&NIGHT” section, descriptions and screenshots below will focus on the AUTO, B/W, EXT modes accordingly. Models with or without LED is the key to the defaults of D&N here. ■ D->N (AGC): To adjust the setting value of Day to Night (AGC). ■... - Page 15 ■ BURST: To enable or disable the Burst function. ■ IR SMART: To enable or disable the IR Smart function. Turning it on can further adjust the level and area as shown below. ■ RETURN: Select RET to go back to the previous page; or select SAVE&END to save the settings and then exit OSD.
- Page 16 2.7 NR Entering this section can adjust the setting of 2DNR/3DNR function for noise reduction under night or low light environment. ■ 2DNR: 2DNR function has LOW/MIDDLE/HIGH/OFF, 4 levels adjustable. ■ 3DNR: 3DNR function has LOW/MIDDLE/HIGH/OFF, 4 levels adjustable. ■ RETURN: Select RET to go back to the previous page;...
-
Page 17: Special
2.8 SPECIAL In the “SPECIAL” section, lots of items can be adjusted. The following descriptions and screenshots mainly focus on the settings of D-EFFECT, MOTION, PRIVACY, DEFECT, and RS485. ■ FREEZE: To enable of disable the Freeze function. ■ MIRROR: To enable of disable the Mirror function. - Page 18 ■ SELECT: To select the Area (1/2/3/4) applying Motion Detect function. ■ DISPLAY: To enable or disable the Display area applying Motion Detect function. ■ SENSITIVITY: To adjust the value of Sensitivity applying Motion Detect function. ■ COLOR: To select the Color from Green, Red, Blue, and White to apply to the Motion Detect area. ■...
- Page 19 ■ SELECT: To select the Area (1/2/3/4) applying Privacy Mask function. ■ DISPLAY: To select the Display mode for Privacy Mask Area from: COLOR, INV., MOSAIC, OFF. ■ COLOR: To select the Color for Privacy Mask Area from: Green, Yellow, Red, Blue, White, Black, Cyan, and USER.
- Page 20 ■ WHITE DPC: To enable or disable White DPC function. Turning it on can further adjust the POS/SIZE and other related setting values as shown below. ■ BLACK DPC: To enable or disable Black DPC function. Turning it on can further adjust the POS/SIZE and other related setting values as shown below.
- Page 21 ■ CAM ID: To select the Camera ID value from 0 to 255. ■ ID DISPLAY: To enable or disable the ID Display function. ■ BAUDRATE: To adjust the Baud rate value from: 38400/19200/9600/4800/2400. ■ RETURN: Select RET to go back to the previous page; or select SAVE&END to save the settings and then exit OSD.
-
Page 22: Adjust
2.9 ADJUST In the “ADJUST” section, lots of items can be adjusted. The following descriptions and screenshots mainly focus on the settings of SHARPNESS and MONITOR. ■ LEVEL: To adjust the value of Sharpness Level. ■ START AGC: To adjust the value of Start AGC. ■... - Page 23 ■ GAMMA: To adjust the Gamma value of the LCD Monitor. ■ BLUE GAIN: To adjust the Blue Gain value of the LCD Monitor. ■ RED GAIN: To adjust the Red Gain value of the LCD Monitor. ■ RETURN: Select RET to go back to the previous page; or select SAVE&END to save the settings and then exit OSD.
-
Page 24: Exit
2.10 EXIT In the "EXIT" section, the following descriptions and screenshot focus on the settings of SAVE&END, RESET, and NOT SAVE. ■ SAVE&END: To Save the settings and then exit OSD. ■ RESET: To Restore all settings to the Factory Defaults. Please note that CAMERA TITLE and LANGUAGE will not be restored.
Need help?
Do you have a question about the AHD 22 Series and is the answer not in the manual?
Questions and answers