Engine Starting; Before Operation; Operation; Parking - Rayco RG25HD Operator, Service, Maintenance, Parts Manual

While the machine is in operation, constantly survey the area
around the machine in order to identify potential hazards as
hazards become visible around the machine.
It may not be possible to provide direct visibility on large
machines to all areas around the machine. Appropriate job
site organization is required in order to minimize hazards that
are caused by restricted visibility. Job site organization is a
collection of rules and procedures that coordinates machines
and people that work together in the same area. Examples
of job site organization include the following:
• Safety instructions
• Controlled patterns of machine movement and vehicle
movement
• Workers that direct traffic to move when it is safe
• Restricted areas
• Operator training
• Warning symbols or warning signs on machines or
on vehicles
• A system of communication
• Communication between workers and operators prior
to approaching the machine

Engine Starting

If a warning tag is attached to the start switch or to the controls,
do not start the engine. Also, do not move any controls.
Move all hydraulic controls to the NEUTRAL position before
you start the engine.
Engine exhaust contains products of combustion which
can be harmful to your health. Always start the engine in
a well ventilated area. Always operate the engine in a well
ventilated area. If you are in an enclosed area, vent the
exhaust to the outside.

Before Operation

Safety information is available in English for this machine.
A list of some of the material is available in the Operation
and Maintenance Manual, "Reference Material". Consult
your Rayco dealer in order to obtain copies of the material.
The information should be reviewed by every person that
operates the machine.
Clear all personnel from the machine and from the area.
Clear all obstacles from the path of the machine. Beware
of hazards such as wires, ditches, etc.
Make sure that all windows are clean. Secure all doors in the
closed position. Secure the windows in the open position
or in the shut position.
Call 811 Before You Dig. One free, easy call gets your utility
lines marked and helps protect you from injury and expense.
800.392.2686
RG25DH Operation • Service • Maintenance • Parts Manual
Know whats below, before you dig. Go to www.call811.com
for more details.

Operation

Only operate the machine controls when the engine is running.
Do not leave the operators station while machine is running.
Before you move the machine, you must be certain that no
one will be endangered.
While you operate the machine and the work tool slowly in
an open area, check for proper operation of all controls and
all protective devices.
Do not allow riders on the machine.
Note any needed repairs during machine operation. Report
any needed repairs to certified service technician.
Use only Rayco Approved Work Tools on this machine. Obey
all the lift restrictions. Refer to Operation and Maintenance
Manual, "Rayco Approved Work Tools" for the approved work
tools and the lift restriction information.
Do not go close to the edge of a cliff, an excavation, or an
overhang.
If the machine begins to sideslip downward on a grade,
immediately turn the machine downhill.
Avoid any conditions that can lead to tipping the machine.
The machine can tip when you work on hills, on banks and on
slopes. Also, the machine can tip when you cross ditches,
ridges or other unexpected obstacles.
Avoid operating the machine across the slope. When possible,
operate the machine up the slopes and down the slopes.
Maintain control of the machine. Do not overload the machine
beyond the machine capacity.
Never straddle a wire cable. Never allow personnel to straddle
a wire cable if equipped.
Know the maximum dimensions of your machine.
Observe all applicable local government regulations when
you use this machine.

Parking

Park on a level surface. If you must park on a grade, chock
the machine.
1. Move the joystick if equipped control slowly to the
NEUTRAL position in order to stop the machine.
2. Move the throttle control lever to the LOW IDLE position.
3. Lower all implements (if equipped) so that the work tool
implement rests firmly on the ground.
4. Move the hydraulic controls if equipped to the NEUTRAL
position.
5. Turn the engine start switch key to OFF position and
remove the key.
Safety
15