Table of Contents
Advertisement
INSTALLATION INSTRUCTIONS: VERTICAL WALL BED HARDWARE KIT WITH FRAME
MODEL CODES:
54877 (Single vertical wall bed)
55991 (Double vertical wall bed)
54386 (Queen vertical wall bed)
*Our more compact model for shipping.
Rockler Woodworking and Hardware
4365 Willow Drive, Medina, MN 55340
1-800-279-4441
1
Advertisement
Table of Contents
Related Manuals for I-Semble 54877
Summary of Contents for I-Semble 54877
- Page 1 INSTALLATION INSTRUCTIONS: VERTICAL WALL BED HARDWARE KIT WITH FRAME MODEL CODES: 54877 (Single vertical wall bed) 55991 (Double vertical wall bed) 54386 (Queen vertical wall bed) *Our more compact model for shipping. Rockler Woodworking and Hardware 4365 Willow Drive, Medina, MN 55340...
- Page 2 HARDWARE Left and right of the frame Upper and lower half frame supports Middle frame supports Long center frame support Upper and lower frame supports Flat bars Pistons (non locking) Mattress Supports Mounting plates (left and right) Saddle locking plates Brackets to attach wall bed to wall x12 x12 Door brackets...
- Page 3 Wrench Allen Key #4 Allen Key #5 x16 x16 x16 Threaded inserts x16 x16 x16 M8 x 16mm Screws x26 x26 x26 #10 x 55mm Screws (Step 12) x32 x52 x52 #8 x 15mm Screws (Steps 11-12) #10 x 15mm Screws #10 x 30mm Screws M5 x 15mm Screws M6 x 30mm Bolts...
- Page 4 VERTICAL WALL BED Overall Cabinet Dimensions Conversion Table DIMENSIONS Inside Measurements Width Depth Height Single 41 3/8 14 1/2 Double 57 1/4 14 1/2 ######### Queen 63 5/16 14 1/2 ######### Outside Measurements Width Depth Height Single 42 7/8 ######### 78 1/2 Double 58 3/4...
- Page 5 DRILLING GUIDE The holes should be 3/8” in diameter and 1/2” deep for threaded inserts. Front Back 16 " 8 " 16 " Bottom All measurements are for 3/4’’ thick board. *See full sized template in product box.
-
Page 6: Installing The Mounting Brackets
INSTALLING THE MOUNTING BRACKETS Right side Wood Left side U + T Bottom ASSEMBLING THE CABINET * See guide on page 4 for suggested cabinet dimensions. -
Page 7: Securing To The Wall
SECURING TO THE WALL * Needs to be secured into at least two wood or metal studs. *Nylon wall anchors are NOT recommended * Professional installation recommended. ASSEMBLING THE FRAME Attach B and C to A for both the right and left sides of the frame. *Ensure that all of the tabs are pointing towards each other. - Page 8 Attach E and F to D. The tabs on E must face the inside of the frame. All tabs should be facing the floor. Insert E into the assemblies from step 4.1.
- Page 9 Bolt F to the two frame halves from step 4.1. INSTALLING THE SLATS Place P on one end of each slat. Attach two slats together with Q. Insert P and Q into their designated holes along the frame. Insert all of the slats except for 4 for the single and double, and 6 for the queen (please see next page to see which slats to skip).
- Page 10 Example below works for both Please do not insert slats in row 11 for the queen single and double. Pivot point Start from this side. Pivot point For each bed size, do not insert slats in row #8, or the slats in the last row.
- Page 11 INSTALLING THE FRAME ONTO THE MOUNTING BRACKETS Place the bearing into the saddle on the mounting bracket. Secure the bearing in place with:...
- Page 12 INSTALLING THE PISTONS TO THE CABINET Tilt the frame inside past the edge of the cabinet to install the pistons on the mounting brackets. INSTALLING THE STOPPER Install the temporary stoppers onto the Stopper top corners of the bed cabinet. Install the permanent stopper on the inside top of the cabinet where it will allow for the door to close flush to the front of the cabinet.
-
Page 13: Installing The Legs
INSTALLING THE LEGS 10.1 Secure the legs to the bed frame. Do not overtighten. 10.2 Install tube to both legs. INSTALLING THE DOOR BRACKETS 6” 6” The door brackets must point downward. Install the door brackets in alignment with the support bars on the bed frame. 3/8”... -
Page 14: Installing The Doors
INSTALLING THE DOORS 12.1 Hook the door brackets onto the frame and push down until they are firmly in place. Center the doors on the frame. For this step 12.2 Attach the doors to the frame while putting weight on the frame to keep the bed x 20 x 28 open. - Page 15 INSTALLING THE REMAINING SLATS Insert P and Q into their designated holes along the frame. Insert all of the remaining slats. INSTALLING THE MATTRESS SUPPORTS Insert the mattress supports into the designated holes on the bed frame.
- Page 16 USING THE WALL BED The wall bed is assembled and shown in Pivot the leg towards the inside of the unit. Make lowered position. sure that the leg is fully retracted. Pull up gently to close. The leg serves as a mattress retaining system.