Subscribe to Our Youtube Channel
Related Manuals for Moeller XVH-3 0 Series
Summary of Contents for Moeller XVH-3 0 Series
- Page 1 Building Automation Industrial Automation Systems Device Description Embedded HMI XVH-3x0 01/05 AWB2776-1559GB Think future. Switch to green.
- Page 2 No part of this manual may be reproduced in any form (printed, photocopy, microfilm or any other process) or processed, duplicated or distributed by means of electronic systems without written permission of Moeller GmbH, Bonn. Subject to alteration without notice.
- Page 3 Warning! Dangerous electrical voltage! Before commencing the installation • Disconnect the power supply of the device. • Ensure a reliable electrical isolation of the low voltage for the 24 volt supply. Only use power supply units complying with • Ensure that devices cannot be accidentally restarted. IEC 60364-4-41 (VDE 0100 Part 410) or HD 384.4.41 S2.
- Page 5 Hardware Device Description Embedded HMI XVH-3x0 Notes 01/05 AWB2776-1559GB © by Moeller GmbH...
-
Page 6: Table Of Contents
14 Disposal......................29 15 Technical Data....................30 16 EU Conformity/Safety ..................32 16.1 EMC ........................32 16.2 Explosion protection ................... 32 16.2.1 Zone 22, Category 3D ..................... 32 17 Safety / North American Approvals..............33 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 7: Explanation Of Symbols
Information pictograms indicate the following: Important information about the product or the relevant section of the document, requiring the particular attention of the reader. The “Information” pictogram has the following meaning: Indicates important and instructional information. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 8: Introduction
The operating system, the application programs and data can be exchanged easily without any other technical resources. The PANELs use the benefits of a seamless Ethernet and IT-based (WEB-based) automation solution and thus offer an unlimited range of possible applications. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 9: Aim And Purpose Of This Document
2.3 L IST OF DOCUMENTS Subject Document Doc. No. Installation Installation instructions General wiring instructions AWB2776-1569 Networks Networks in brief AWB2776-1568 Windows CE PANEL with WindowsCE AWB2776-1553 (this list of documents is not final) 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 10: Device Versions
(for IP65) • • Power supply plug connector • • CompactFlash cover for the CompactFlash slot • Resistive touch pen 3.2 O PTIONS • • OS Flash • • Additional fixing brackets for IP65 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 11: Commissioning
The Ethernet, ComModule (e.g. CAN) and Supply terminals are located on the right of the device when viewed from the rear. The terminal for the USB interface is located on the left of the device. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 12: General Notes On Cabling
Phönix Order No. 1757022; Supplied with unit (view from the wiring side) +24 VDC GND +24 VDC +24 VDC power supply Functional ground, connected with housing (connection not compulsory) 0 V power supply (connected with housing) 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 13: Ethernet
A crossover cable must be used for connecting one device with another. A 1:1 cable must be used when using a hub in the connection. Further information: Installation instructions, General wiring instructions [1] 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 14: Usb Device
Only use USB standard cables with a shield. When preparing the cables it must be ensured that the cable shield is correctly connected to the connector housing. The maximum permissible cable length is 5 m. Further information: Installation instructions, General wiring instructions [1] 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 15: Expansion Module Interfaces (Commodule) Optional
The terminating resistor must be provided externally, e.g. in the connector, and is not part of the device. The CAN connector is not provided with a supply for third-party devices. Further information: Installation instructions, General wiring instructions [1] 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 16: 4.6.2 Mpi
The terminating resistors must be provided externally, e.g. in the connector, and are not part of the device. The 5V must not be used as a power supply for systems of other suppliers. Further information: Installation instructions, General wiring instructions [1] 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 17: System Control Button (Ctrl)
The Control button is located on the side of the CompactFlash slot and the Test LED. Ensure the accessibility of the device when it is mounted. Viewed from the rear, the Control button is accessible on the left. Control button 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 18: System Settings
Device Description Embedded HMI XVH-3x0 Hardware System settings YSTEM SETTINGS This is where network, display, date/time settings etc. are entered. These can be set via Start ⇨ Programs ⇨ Control Panel. Further information: PANEL with WindowsCE [3] 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 19: Compactflash Slot
XHV. The CompactFlash card is not supplied with the Panel . We recommend the use of the CompactFlash cards supplied by Moeller in order to ensure interference-free operation. Moeller cannot offer support and does not accept any liability for consequential damage arising from the use of CompactFlash cards offered by other suppliers. -
Page 20: Expansion And Configuration Options
Interventions on the device must only be carried out after the power supply has been switched off. During operation device components carry dangerous voltage. Safety precautions concerning electrostatic discharge (ESD) must be observed when making interventions on the device. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 21: Function And Control Leds
CMM ACT (green) Lit briefly Bus active (data traffic) CF card CF ACT (red) Lit briefly (chap. 7) CF card access ETHERNET LINK (green) Active network connected and detected ACT (yellow) Flashing Ethernet active (data traffic) 01/05 AWB2776-1559GB © by Moeller GmbH... - Page 22 Device Description Embedded HMI XVH-3x0 Hardware Function and Control LEDs Cutout of the XVH with a view of the FlashCard and Control LED without the CompactFlash cover. 01/05 AWB2776-1559GB © by Moeller GmbH...
-
Page 23: Mounting Instructions
Ensure that operating elements (Control button, CF card) and terminals are still accessible when the device is mounted. The front panel should not exceed a maximum thickness of 5 mm, due to the clamping range of the fixing brackets. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 24: Standard Front
3. Fix the device at two corners on the top and the bottom with the 4 fixing brackets supplied. 4. Additional fixing brackets are required for mounting to IP 65 (optional) or in the Ex Zone 22. These brackets are positioned in the middle of each side. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 25: Mechanical Dimensions
Hardware Device Description Embedded HMI XVH-3x0 Mounting Instructions 10.3 M ECHANICAL DIMENSIONS Einbautiefe Standard front Resistive touch 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 26: Front Panel Cutout Standard Front
RONT PANEL CUTOUT STANDARD FRONT Front panel cutout: 198.0 +1/-0 mm x 142.0 +1/-0 mm 198.0 +1/-0 The front panel should not exceed a maximum thickness of 5 mm, due to the clamping range of the fixing brackets. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 27: Notes On The Touch Screen
Do not expose the front of the device to solvents which may corrode and destroy the plastic frame and foil (frame material: polycarbonate (PC); Foil material: polyester (PET); Display pane: non-reflective glass; Carrier plate: aluminum). 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 28: Resistive Touch
Only clean the touch foil with a non-abrasive cleaning material. Do not expose the front of the device to solvents which may corrode and destroy the foil (foil material: polyester (PET); Carrier plate: aluminum). The touch panel must only be actuated with a special pen or with a finger. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 29: Display Technology, Backlight
Therefore avoid the frequent switching on and off of the backlight or the entire system. Minimising the brightness required is more effective than reducing the frequent on/off switching. Further information: PANEL with WindowsCE [3] 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 30: Maintenance And Repair
Support Moeller.(www.moeller.net/Support) The warranty is not applicable if any modifications are made to the device that are not described in this document. Transport Only the original packaging must be used for transporting the device. 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 31: Disposal
Housing: Galvanized sheet steel Front plate: Aluminum, Peraluman 101 anodized IR frame: Polycarbonate (PC); Front glass: Non-reflective glass Foil: Autotype polyester (PET); Materials Packaging Boxes: Cardboard Transport protection: TFL foam (polyethylene) Plastic bag: Polyethylene 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 32: Technical Data
2ms from undervoltage (19.2V) Protection agains reverse polarity Fuse protection Yes (internal fuse) Potential isolation The 0V- connection is directly connected to the housing potential (GND) Power consumption max. 14W / 24VDC Inrush max. 2.5A2s 01/05 AWB2776-1559GB © by Moeller GmbH... - Page 33 EMC (CE) EN 61000-6-2, EN 61000-6-4 EN 61000-6-3 EN 61131-2 Safetyt EN60950 UL60950 (UL) Explosion protection All standard devices Zone 22, Category 3D (CE) Product standards EN 50178, Electrical equipment for use in electrical installations 01/05 AWB2776-1559GB © by Moeller GmbH...
-
Page 34: Eu Conformity/Safety
Electrical apparatus for explosive gas atmospheres. General requirements EN 50281-1-1 Electrical apparatus for use in the presence of combustible dust Part 1-1: Electrical apparatus with protection by enclosures – design and testing EN 13463-1 Non-electrical equipment for potentially explosive atmospheres 01/05 AWB2776-1559GB © by Moeller GmbH... -
Page 35: Safety / North American Approvals
17 S AFETY ORTH MERICAN PPROVALS The standards EN60950-1 and UL60950 were used for the assessment of electrical safety. The XVH-330/340-57 Systems are approved for the USA and Canada. UL60950 (UL File No. E208621) 01/05 AWB2776-1559GB © by Moeller GmbH... - Page 36 Device Description Embedded HMI XVH-3x0 Hardware Safety / North American Approvals 01/05 AWB2776-1559GB © by Moeller GmbH...
- Page 37 Hardware Device Description Embedded HMI XVH-3x0 01/05 AWB2776-1559GB © by Moeller GmbH...
- Page 38 Device Description Embedded HMI XVH-3x0 Hardware Moeller GmbH Industrial Automation Hein-Moeller-Str. 7-11 D-53115 Bonn +49 (0) 228-602-0 +49 (0) 228-602-2275 E-Mail info@moeller.net Internet http://www.moeller.net 01/05 AWB2776-1559GB © by Moeller GmbH...
Need help?
Do you have a question about the XVH-3 0 Series and is the answer not in the manual?
Questions and answers