Download Print this page
Elkay SWIRLFLO ENOB2-8C Installation, Care & Use Manual

Elkay SWIRLFLO ENOB2-8C Installation, Care & Use Manual

Refrigerated fountains with flexi-guard

Advertisement

Quick Links

SWIRLFLO Refrigerated fountains with FLEXI-GUARD
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices to
available water lines. This can, however, cause electrical feedback in the plumbing circuit, which results in
an "electrolysis" effect occurring in the fountain. This may result in water which has a metallic taste to it or
has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the installation,
and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation. Any
drain fittings provided by the installer should be made of plastic which will electronically isolate the fountain
from the remainder of the building's plumbing circuits.
ENOB2-8C, ENOB2-8RAC
INSTALLATION, CARE & USE MANUAL
T M
ENOB2-8C
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left with building owner
for future reference.
Service to be performed by authorized service personnel only.
ENOB2-8RAC
1
T M
98005C (REV. B - 3/05)

Advertisement

loading

Summary of Contents for Elkay SWIRLFLO ENOB2-8C

  • Page 1 ENOB2-8C, ENOB2-8RAC INSTALLATION, CARE & USE MANUAL SWIRLFLO Refrigerated fountains with FLEXI-GUARD ENOB2-8C ENOB2-8RAC INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left with building owner for future reference.
  • Page 2 ENOB2-8C, ENOB2-8RAC 98005C (REV. B - 3/05)
  • Page 3: Required Tools And Materials

    ENOB2-8C, ENOB2-8RAC REQUIRED TOOLS AND MATERIALS These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: Special Tools Item Description Quantity NONE Additional Materials Item Description Quantity Unplated copper inlet pipe Service Stop 1.
  • Page 4 ENOB2-8C, ENOB2-8RAC Attach waste tube (1-1/4” O.D.) to 1-1/4” O.D. slip trap (provided by others). Connect the fountain drain waste tube to the building 24, 25 sanitary sewer system. Connection should be made in compliance with local plumbing code requirements. (Note: Plumbing trap is not included with the fountain).
  • Page 5 ENOB2-8C, ENOB2-8RAC ENOB2-8C ENOB2-8RAC Figure 7 - Solenoid Assembly CONNECT TO FOUNTAIN SENSOR WIRING CONNECTOR 45, 46, 47 Figure 8 - Regulator Assembly 98005C (REV. B - 3/05)
  • Page 6 ENOB2-8C, ENOB2-8RAC See Fig. 10 Figure 9 - Exploded View BUBBLER DETAIL Basin NOTE: When installing replacement bubbler and pedestal, tighten nut (Item 5) only to hold parts snug in position. Do Not Overtighten. Figure 10 - Bubbler Assembly 98005C (REV. B - 3/05)
  • Page 7 ENOB2-8C, ENOB2-8RAC See Fig. 10 See Fig. 10 Figure 11 - Fountain Body Assembly Figure 12 - Push Button Assembly Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing.
  • Page 8: Parts List

    ENOB2-8C, ENOB2-8RAC Installation Package PARTS LIST The components for installation are packed in three ITEM NO. PART NO. DESCRIPTION separate boxes, regardless of the type of unit being installed. The boxes contain the following: 56073C Bubbler Assy 40322C Orifice Assy 56011C Housing Assembly Box No.

This manual is also suitable for:

Swirlflo seriesSwirlflo enob2-8rac