CALI LipLeds LLED8700-OL Installation Instructions Manual

lipLEDs
Installation Instructions
Frosted Lens Cover
(#LLED8700-OL-LF)
6.5"
3.9" or 6.5"
6.5"
End Cap
2"
(#LLED8700-OL-EC)
3.9" or 6.5"
2"
2"
6"
WARNING
• Do not power lipLEDs when coiled or bunched together.
2"
Maintain half inch spacing between parts when lit
• Do not cover lipLEDs as the covering may cause it to overheat, melt, or ignite
3.95"
• Do not puncture or damage lipLEDs
• Do not route lipLEDs through walls, doors, windows, or building structures
• Do not roll out lipLEDs on rough surfaces or over sharp corners.
6"
• Do not use lipLEDs if damaged, such as, broken outer jacket, loose
2"
connections, or frayed wire insulation. Inspect periodically
• Do not secure lipLEDs with staples, nails, or like means that might
damage the insulation. Secure using mounting clips or mounting channel
3.95"
• Do not submerge lipLEDs in liquid or install near standing water or
other liquids
• Do not install lipLEDs where it is subject to continuous flexing
• Do not mount lipLEDs inside cabinets, tanks, or enclosures of any
kind without proper ventilation
2"
• Do not run lipLEDs at an operation temperature exceeding 65C or 149F or
below -20C or -4F
™
6.5" increments up to max run
± 0.125" cutting tolerance
*See max run for more information
6.5" (2.5W) or 3.9" (5.5W) increments up to max run
± 0.125" cutting tolerance
*See max run for more information
Aluminum Extrusion
8' Maximum extrusion and lens length
6.5" increments up to max run (#LLED8700-OL)
(Dry Location field cuttable)
± 0.125" cutting tolerance
*See max run for more information
2" increments up to max run
± 0.125" cutting tolerance
6.5" (2.5W) or 3.9" (5.5W) increments up to max run
*See max run for more information
± 0.125" cutting tolerance
(Run lengths required)
*See max run for more information
2" increments up to max run
8' Maximum extrusion and lens length
± 0.125" cutting tolerance
(Dry Location field cuttable)
*See max run for more information
Specify Length (19.7"Assembly Increments)
2" increments up to max run
(Add 2.5" to run for end cap and strain relief)
± 0.125" cutting tolerance
*See max run for more information
(Run lengths required)
6" increments up to max run
*See max run for more information
2" increments up to max run
± 0.125" cutting tolerance
*See max run for more information
3.95" increments up to max run
± 0.125" cutting tolerance
*See max run for more information
Specify Length (19.7"Assembly Increments)
(Add 2.5" to run for end cap and strain relief)
6" increments up to max run
*See max run for more information
2" increments up to max run
± 0.125" cutting tolerance
*See max run for more information
3.95" increments up to max run
± 0.125" cutting tolerance
*See max run for more information
8' Maximum extrusion and lens length
2" increments up to max run
8' Maximum extrusion and lens length
± 0.125" cutting tolerance
*See max run for more information
8' Maximum extrusion and lens length
Lens and extrusion shipped in
8' sections (field cuttable)
CALIFORNIA ACCENT LIGHTING, INC.
2034 E. Lincoln Ave. #431, Anaheim, CA 92806
ph. 800.921.CALI (2254) or 714.535-7900 \ fx. 714.535.7902
8' Maximum extrusion and lens length
info@calilighting.com \ calilighting.com
© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.
Power Connector
(#LLED8700-PC)
End View
1.20"
• Use only standard outdoor extensions cords, such as, SW, STW, STOW,
SJW, SJOW, SJTW, and SJTOW
• Ground Fault Circuit Interruptor (GFCI) protection is required on
circuits or outlets when lipLEDs is used for outdoor applications
• Surge protector must be set up for electrical power system to avoid
damaging lipLEDs lighting system
INSTALLATION TOOLS REQUIRED
• Electric Compound Miter Saw
• 14.4 to 28 Volt Cordless Drill
• Wire Strippers for 22 and 15
gauge wire
• Pliers
1.20"
• Wire Cutter
• Phillips Bits - Sufficient Quantity
• Carbide Masonry Drill Bits -
Sufficient Quantity
1.46"
LLED8700-OL
Overview
1.46"
IMPORTANT VERIFY CORRECT
LUMINAIRE WAS RECEIVED WITH
CORRECT COLOR TEMPERATURE
AND VOLTAGE BEFORE CUTTING
OR INSTALLING. CALI WILL NOT
BE RESPONSIBLE IF INCORRECT
LUMINAIRE IS INSTALLED.
• Concrete Tapcon Screws
• Self Drill Metal Screws #4 x 1/2"
- Sufficient Quantity
• Electrical Cords
• Electrical Three Way
• Safety Glasses
• Measuring Tape
• Marker
• Chalk Line
1 of 12
.78"
.75"
5.5W
.78"
.75"
5.5W