wattstopper Legrand Miro MRDS10 Quick Start Manual

DESCRIPTION
The MRDS10 To u c h s c re e n is a combination room and house
level scene co n t ro l ler with the capacity to also co n t rol up to
30 individual dev i ce groups. The menus and co n t rol functions
a re acce ssed by touching the labels and icons that appear on
the scre e n .
The to u c h s c reen has a help system built into
each page. To acce ss help for a particular page,
p re ss the question mark button at the top of
the page.
Setup Screen
A to o l b ox icon appears on the HOME PAGE. Use
the to o l b ox icon to acce ss the setup scre e n s .
Status LED Indicator & Wake-up Button
The MRDS10 also uses a multi-co lor LED (gre e n / a m b e r / re d )
to indica te dev i ce status. Dire c t ly below the LED there is a
s i n g le push-button. Momenta r i ly pre ss this button to wake
up the to u c h s c reen when in power save mode.
The LED can display one of three co lo rs: green, ye l low
(amber, a combination of red and green), or red. The co lo r
can be co n stant, or can flash at one of three ra tes to
d i stinguish re p o r ted conditions. To determine the flash ra te ,
count the number of flashes in 5 seco n d s :
5 fla s h e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hz
10 fla s h e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Hz
15 fla s h e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Hz
MRDS10 LED Indications are as fo l low s :
C o lo r B e h a v i o r M e a n i n g
n o n e O f f D ev i ce is not powe red or is in "sle e p "
m o d e .
G re e n On, not fla s h i n g D ev i ce is powe red, has a house ID,
o p e rating normally.
G re e n Flashing @ 2 Hz During binding, dev i ce is excluded, but
can be added.
A m b e r On, not fla s h i n g D ev i ce does not have a house ID.
A m b e r Flashing @ 2 Hz D ev i ce is part of a binding pro ce ss, either
G roup or Room. Binding was sta r ted by
some other dev i ce and must be sto p p e d
on the other dev i ce .
A m b e r Flashing @ 3 Hz D ev i ce is the master of a binding pro ce ss .
Binding was sta r ted on this dev i ce and
m u st stop on this dev i ce .
R e d Flashing @ 2 Hz D ev i ce has enco u n te red an erro r. An
i n valid command was atte m p te d .
Caution: Battery Vo l tage is Low ~ 10s
every 1-2 minute s
R e d Flashing 3 Hz Shutting down To u c h s c reen due to low
b a t tery co n d i t i o n
W i re le ss To u c h s c reen Contro l le r
Application Assistance
The wire le ss network may co n tain a variety of wire le ss
d ev i ces. Instructions for installation, binding opera t i o n s ,
and use are included with the re levant wire le ss dev i ce s .
A p p l i cation support information and installation guides fo r
Watt Sto p p e r / L e g rand wire le ss network dev i ces are
a va i l a b le at www. w a t t sto p p e r. com. Comple te the physica l
i n stallation and binding of all other wire le ss dev i ces in the
n e t work befo re co n figuring the to u c h s c reen.
Scene Binding
Bind other wire le ss dev i ces in the system to appro p r i a te
g roups and rooms befo re you attempt to exe c u te sce n e s
f rom the MRDS10. Use an appro p r i a te scene co n t ro l le r ,
s cene re m o te or a MR232 and a PC running a te r m i n a l
e m u l a to r to setup and re co rd scenes. Once re co rded, the
MRDS10 can be included in groups and sce n e s .
C reating new scenes using the MRDS10 To u c h s c reen is
b eyond the scope of this guide. Once you are familiar with
the basic operations described in this guide, you can use
the help screens to learn how to cre a te new sce n e s .
MIRO TOUCHSCREEN SETUP INSTRUCTIONS
B e fo re pro ceeding please read the fo l low i n g :
• All screen setups must be initiated from the
H O M E PAGE using the to o l b ox icon.
• To setup your screen fo l low the instructions give n
h e re along with the prompts that are given on the
to u c h s c reen.
• Remember to use the help scre e n s
• U n le ss sta ted otherwise, these instructions ass u m e
that the Miro system is co n fig u red befo re setting up
the to u c h s c reen.
M R D S 1 0
.