Table of Contents
Advertisement
Quick Links
P.O Box 1118 Bayswater, Vic, 3153 Australia
Phone: International ++614 2902 9083
Australia (04) 2902 9083 (03 8685 8230)
Website
E mail:
PROFESSIONAL
SERIES
FOR
HOBBY KING
E
S
LECTRONIC
PEED
HOBBY KING R/C IS AN
THE
PRO
GROUP
Thank you for purchasing this Microprocessor based Electronic Speed Control
Ch # 5 IS NO LONGER USED FOR PROGRAMMING.
THIS NEW SYSTEM CAN USE ANY
THIS IS IDENTICAL TO THE RE-LABELED R/C SOLD UNDER THE FOLLOWING BRANDS:
IN AUSTRALIA AS
IT IS MOST IMPORTANT THE TX ISET FOR
RCS-PRO
EVERY
2. THE DECODER PCB, INTO WHICH THE
USE ONLY OPERATING PROGRAM
RCS-PRO
THE HAVE CONSTANT BRIGHTNESS DIRECTIONAL LIGHTS & 4 SOUND TRIGERS.
THE FOLLOWING MAXIMUM VOLTAGES MENTIONED ARE THE
ACCOUNT THE FACT FULLY CHARGED BATTERIES CAN & DO EXCEED THE
USE 7.2v – 24 v FOR THE
We tested this system three times during manufacture. It was working normally when it left our factory.
If damage in transit has occurred, please return to place of purchase for attention.
THIS ESC IS GUARANTEED FOR ONE YEAR.
INCLUDED ARE ONE OR THE OTHER OF THE FOLLOWING COMPONENTS:
# PRO-3b, # PRO-6b OR # PRO-PnPb ECS's PLUS ONE PLUG IN PUSHBUTTON CABLE.
You will supply the 2.4 Ghz 4 channel (or more) digital Proportional
You will also supply a locomotive or trail car, the 7.2 – 24 volt traction batteries (depending on ESC), a fuse,
an ON-OFF switch and wires where necessary to connect the ESC to the battery and motor(s).
Where soldering is necessary, we recommend a low wattage soldering iron and resin core solder.
DO NOT ATTEMPT TO ALTER THE TUNING OF THE RADIO EQUIPMENT.
DO NOT USE RADIO CONTROL EQUIPMENT IN THUNDERSTORMS.
CHILDREN UNDER 12:
http://rcs-rc.com
Info@rcs-rc.com
ESC's
C
(ESC)
ONTROLLER.
"B"
GROUP R/C & MUST USE
"B"
OPERATING PROGRAM.
INSTRUCTIONS.
COPETR-X.
IN THE USA AS
THEY ARE SOLD WITH TWO DIFFERENT RX's AVAILABLE.
SYSTEM IS IN TWO PARTS CONNECTED BY A PLUG IN 4 X WAY CABLE.
1. THE POWER IN – MOTOR CONTROL OUT, PCB &
SERVO LEADS ARE NOT NEEDED.
DO NOT CONNECT TO MAINS POWER (110 – 240V AC).
# PRO-3b & # PRO-6b ESC's ARE DESIGNED TO RUN ON BATTERIES.
THE # PRO-PnPb CAN BE USED WITH TRACK AND BATTERY POWER.
RCS-PRO
ADULT SUPERVISION RECOMMENDED DURING USE.
PROVIDED IN INSTRUCTIONS.
Page # 1 Introduction.
Page # 2 Installing the ESC.
Page # 3 Installing the RX into the # DEC-U.
Page # 4 Setting up the system.
Page # 5 Calibrating the system.
Page # 6 Programming the system.
Page # 7 Operating the System.
R/C
Page # 8 MU'ing Consists of Locos.
PLEASE NOTE. PDF WIRING INSTRUCTIONS ARE HERE:
http://www.rcs-rc.com/pages/instructions
HOBBY KING
2.4 GHz R/C WITH 4 OR MORE CHANNELS.
EXCEED
"ACRO"
HOBBY KING
RX IS SIMPLY PLUGGED IN UPSIDE DOWN.
# PRO-3b, # PRO-6b OR # PRO-PnPb ECS's.
CAUTION
TABLE OF CONTENTS
Binding the RX.
Speed & Direction control.
Using Sound Trigger functions.
Trouble shooting.
& IN HONG KONG AS
& MODE # 1
OR
MODE # 2.
PRO-Bv1.
NOMINAL
VOLTAGE & TAKE INTO
NOMINAL
HOBBY KING
(ESC)
system.
TURBORIX.
VOLTAGE.
R/C.
Advertisement
Table of Contents
Related Manuals for Remote Control Systems PROFESSIONAL ESC's Series
Summary of Contents for Remote Control Systems PROFESSIONAL ESC's Series
- Page 1 TABLE OF CONTENTS PROVIDED IN INSTRUCTIONS. Page # 1 Introduction. Page # 2 Installing the ESC. P.O Box 1118 Bayswater, Vic, 3153 Australia Page # 3 Installing the RX into the # DEC-U. Phone: International ++614 2902 9083 Page # 4 Setting up the system. Australia (04) 2902 9083 (03 8685 8230) Binding the RX.
- Page 2 - 2 - RCS-PRO INSTALLING ESC’s. HOBBY KING IS A GROUP “B” R/C & THIS ESC MUST USE THE PRO-Bv1 OPERATING PROGRAM. RCS-PRO ESC’s can use a HK TR6a 4 or more channel 2.4 GHz digital proportional R/C TX & RX with servo outputs. We have conducted development &...
- Page 3 - 3 - PLACING RX ANTENNA. Other than with brass locos, it does not matter where you place the antenna(s). We have at least 200’ + range with the system in plastic locos. There is NO “glitching” or “Rusty Bolt Effect”. N.B.
- Page 4 - 4 - RCS-PRO SETTING UP THE ESC’s. HOBBY KING TR6a THESE INSTRUCTIONS REFER TO THE 2.4 GHz 6 CHANNEL R/C. LAYOUT OF THE HK-T6a TRANSMITTER. YOU CAN USE EITHER MODE # 1 or MODE # 2. YOUR SYSTEM WILL LIKELY BE DELIVERED CORRECTLY SET UP FOR THE MODE. HOWEVER IT IS A GOOD IDEA TO CHECK THE SETTINGS VIA THE SUPPLIED COMPUTER PROGRAM.
- Page 5 - 5 – 2. CALIBRATION. The 2 step in system preparation is to calibrate the direction & throttle sticks. Even though this step is only needed once when first setting up a new ESC, from time to time it is advisable to run through the procedure. A pushbutton is supplied for both Calibration and system Programming.
- Page 6 - 6 – 3. PROGRAMMING. RCS-PRO Operating features of the system can be programmed from the TX using the supplied pushbutton. Programming can only take place when the system is in neutral. 3.1 START VOLTAGE. This feature is designed to equalise the starting voltage of dissimilar locos. 3.2 TOP SPEED VOLTAGE.
- Page 7 - 7 - RCS-PRO OPERATING THE ESC’s. 4. HOW TO OPERATE AFTER COMPLETING CALIBRATION & PROGRAMMING. THE THROTTLE STICK MUST BE ALL THE WAY DOWN BEFORE TURNING SYSTEM ON. Always turn the TX on first. Then turn the loco ON. The loco will give a slight jerk (See page # 8) & the ESC & loco the lights will stay OFF.
- Page 8 - 8 - RCS-PRO MU’ing LOCO CONSISTS. MULTIPLE LOCOS IN A CONSIST. RCS-PRO ESC’s are capable of MU’ing multiple locos in one consist of locos. You can add as many speed matched locos to the loco consist, as you like. Each loco must be bound to the controlling TX.
Need help?
Do you have a question about the PROFESSIONAL ESC's Series and is the answer not in the manual?
Questions and answers