Kidde Fire Systems PEGAsys Installation, Operation And Maintenance Manual page 9

PARAGRAPH
4-3.4.1 Walk Testing Detectors .................................................................................................................................................. 4-2
4-3.4.2 Walk Test Procedure ...................................................................................................................................................... 4-2
4-3.5 Alarm Simulation Test (AST) .......................................................................................................................................... 4-2
4-3.5.1 AST Procedure ............................................................................................................................................................... 4-3
4-4 Disarming and Rearming Release Circuits .................................................................................................................. 4-3
4-4.1 Disarming Release Circuits .......................................................................................................................................... 4-3
4-4.2 Arming Release Circuits ................................................................................................................................................ 4-3
4-5 Power-Down System ...................................................................................................................................................... 4-3
4-5.1 Power-Down Procedure ................................................................................................................................................. 4-3
4-6 Power-Up System .......................................................................................................................................................... 4-4
4-6.1 Power-Up Procedure ...................................................................................................................................................... 4-4
5 TROUBLESHOOTING AND CORRECTIVE MAINTENANCE ............................................................................................. 5-1
5-1 Introduction ..................................................................................................................................................................... 5-1
5-2 Standard Fault Isolation Techniques ............................................................................................................................. 5-1
5-2.1 Visual Inspection ............................................................................................................................................................ 5-1
5-2.2 Power Checks ................................................................................................................................................................ 5-1
5-3 Troubleshooting ............................................................................................................................................................. 5-1
5-4 Removal and Replacement ........................................................................................................................................... 5-2
5-4.1 Required Tools ............................................................................................................................................................... 5-2
5-4.2 Central Control Module .................................................................................................................................................. 5-2
5-4.3 RX/TX Module ................................................................................................................................................................. 5-2
5-4.4 Field Devices .................................................................................................................................................................. 5-3
6 PARTS LIST .................................................................................................................................................................... 6-1
6-1 Introduction ..................................................................................................................................................................... 6-1
7 INSTALLATION ................................................................................................................................................................ 7-1
7-1 Introduction ..................................................................................................................................................................... 7-1
7-2 Materials Required For Installation ................................................................................................................................ 7-1
7-3 Installation Procedure For Central Control Panel ......................................................................................................... 7-1
7-4 Installation Procedure For Expansion Enclosures ........................................................................................................ 7-1
7-5 Installation Procedure For I/O Motherboard ................................................................................................................... 7-2
7-6 Installation Procedure For Rx/Tx Module (Multi-Loop Only) ........................................................................................... 7-2
7-7 Installation of I/O Modules .............................................................................................................................................. 7-3
7-7.1 Signal Audible Output Module ........................................................................................................................................ 7-3
7-7.2 Relay Output Module ...................................................................................................................................................... 7-4
7-7.3 Agent Release Module ................................................................................................................................................... 7-4
7-7.4 City-Tie Output Module ................................................................................................................................................... 7-4
7-7.6 Power Supply/Charger Assembly .................................................................................................................................. 7-4
7-7.7 Power Supply/Charger Assembly, Expansion Enclosure .............................................................................................. 7-4
7-7.8. Power Supply Communication Connections ................................................................................................................ 7-6
7-8 Connecting AC Power .................................................................................................................................................... 7-6
7-9 Install And Connect DC Power ....................................................................................................................................... 7-6
7-9.1 Battery Enclosure ........................................................................................................................................................... 7-6
7-9.2 Batteries ......................................................................................................................................................................... 7-6
7-10 Field Device Connection To RX/TX Module .................................................................................................................... 7-7
7-10.1 Wiring the RX/TX PC Line ............................................................................................................................................... 7-7
7-11 Output Signal Connection .............................................................................................................................................. 7-9
7-12 External Power Failure Indicator Connection .............................................................................................................. 7-10
7-13 Detector Installation ..................................................................................................................................................... 7-10
7-14 Setting and Adjusting Smoke & Heat Detector Sensitivities ........................................................................................ 7-10
7-14.1 Setting and Adjusting Smoke and Heat Detector Sensitivity Procedure ..................................................................... 7-10
7-15 Addressable Contact Input Device Installation ............................................................................................................. 7-11
7-16 Addressable Relay Output Device Installation ............................................................................................................. 7-11
7-17 Installation Checkout ..................................................................................................................................................... 7-11
7-18 Connection of Peripherals ............................................................................................................................................ 7-11
7-18.1 Connecting a Terminal or Personal Computer ............................................................................................................ 7-11
7-18.2 Connecting a Printer ..................................................................................................................................................... 7-11
TABLE OF CONTENTS (CONT.)
TITLE
v
PAGE