AV-29WS3 SERVICE MANUAL COLOR TELEVISION BASIC CHASSIS AV-29WS3 MUTING POWER SYSTEM CINEMA COLOUR SOUND SURROUND SENSOR DISPLAY MENU I/II TV/TEXT TV/VIDEO TIMER PICTURE MODE CHANNEL RETURN+ SCAN -/-- CHANNEL VOLUME TEXT REVEAL HOLD INDEX SIZE SUBPAGE STORE MODE CANCEL RM-C1010...
AV-29WS3 SPECIFICATIONS Items Contents Dimensions (W × H × D) 81.2cm × 58.42cm × 51.8cm Mass 45kg TV RF System B, G, I, D, K, K1, M Color System TV Mode PAL / SECAM / NTSC3.58 / NTSC4.43 VIDEO Mode PAL / SECAM / NTSC3.58 / NTSC4.43...
AV-29WS3 SAFETY PRECAUTIONS 1. The design of this product contains special hardware, many circuits 8. When service is required, observe the original lead dress. Extra and components specially for safety purposes. For continued pro- precaution should be given to assure correct lead dress in the high tection, no changes should be made to the original design unless voltage circuit area.
AV-29WS3 FEATURES s New chassis design enables use of an interactive on-screen control. s Built-in DIGITAL ECO MODE (ECONOMY, ECOLOGY). s Pure flat CRT produces fine textured picture in every detail. In accordance with the brightness in a room, the brightness and/or s Wide range voltage (110V ~ 240V) for AC power input.
AV-29WS3 FUNCTIONS FRONT PANEL L/MONO IN (VIDEO-3) REAR PANEL COMPONENT VIDEO-1 ( VIDEO-2 ) OUTPUT INPUT INPUT OVER MONO MONO REMOTE CONTROL UNIT [RM-C1010-1H] POWER MUTING SYSTEM CINEMA COLOUR SOUND SURROUND SENSOR DISPLAY MENU TV/TEXT I/II TV/VIDEO TIMER PICTURE MODE...
AV-29WS3 SPECIFIC SERVICE INSTRUCTIONS DISASSEMBLY PROCEDURE CHECKING THE MAIN PW BOARD REMOVING THE REAR COVER 1. To check the back side of the Main PWB. 1) Pull out the chassis. (Refer to REMOVING THE CHASSIS). 1. Unplug the power supply cord.
Page 8
AV-29WS3 [FRONT SIDE] PICTURE TUBE CONTROL BASE FRONT CABINET CHASSIS BASE SPEAKER Fig.2 (X2) SOCKET PWB FRONT CONTROL PWB (2/2) MAIN PWB FRONT CONTROL CLAW B PWB (1/2) SPEAKER AV TERMINAL Fig.2 BOARD (X2) CONTROL BASE CHASSIS BASE CLAW B (×4)
Page 9
AV-29WS3 REMOVING THE CRT CRT CHANGE TABLE * Replacement of the CRT should be performed by 2 or more persons. • After removing the rear cover, chassis etc., 1. Putting the CRT change table on soft cloth, the CRT change table should also be covered with such soft cloth (shown in Fig.
Page 10
AV-29WS3 REPLACEMENT OF MEMORY IC 1. MEMORY IC (6) User setting This TV uses the following memory IC. Check the user setting values in Table 2, and if setting value is Memory IC: IC1702 on MAIN PW Board different, set the correct value.
Page 11
AV-29WS3 SETTING OF SYSTEM CONSTANT SET Setting item Setting content Setting value MULTI TRIPLE SINGLE VIET SYSTEM MULTI COMB TILT ERCMI ERAPU TEXT ERCMI SUPER BASS E/R/C/M/I E/R/C LANGUAGE E/R/C/M/I BILINGUAL B/B SOUND TUNER COLOR AUTO LOCK 1MHz 500KHz 250KHz 156.25KHz...
Page 12
AV-29WS3 USER SETTING VALUES Setting item Setting value SUB POWER CHANNEL POSITION 1 POSITION CHANNEL PRESET REFER TO OPERATING INSTRUCTIONS VOLUME 15 ± 2 TV/VIDEO COMPRESS (16:9) AUTO SHUTOFF CHILD LOCK BLUE BACK VIDEO-2 SET VIDEO LANGUAGE AI VOLUME ON SCREEN DISPLAY...
Page 13
AV-29WS3 SERVICE MENU SETTING ITEMS Service menu Setting item Service menu Setting item 1. IF 1. VCO 5. PRESET 1. PSNS 2. DELAY POINT 2. ACL Do not adjust 3. MUS 4. MAT 2. VC 1. CUTOFF(R/G) 5. FCO 2. DRIVE(R/G/B) 6.
Page 14
AV-29WS3 REPLACEMENT OF CHIP COMPONENT CAUTIONS 1. Avoid heating for more than 3 seconds. 2. Do not rub the electrodes and the resist parts of the pattern. 3. When removing a chip part, melt the solder adequately. 4. Do not reuse a chip part after removing it.
AV-29WS3 SERVICE ADJUSTMENTS ADJUSTMENT PREPARATION 1. You can make the necessary adjustments for this unit with either the remote control unit or with the adjustment equipment and parts as given below. 2. Adjustment with the remote control unit is made on the basis of the initial setting values, however, the new setting values which set the screen to its optimum condition may differ from the initial settings.
Page 16
AV-29WS3 ADJUSTMENT LOCATIONS FRONT CONTROL PWB ASS’Y(1/2) FRONT CONTROL PWB ASS’Y(2/2) FRONT S805 S801 S803 J304 J303 J302 J801 FRONT POWER S804 S806 S802 S801 : CH UP + CN002 S802 : CH DOWN – S901 S803 : MENU CN003...
Page 17
AV-29WS3 BASIC OPERATION IN SERVICE MENU 1. TOOL OF SERVICE MENU OPERATION Operate the SERVICE MENU with the remote control unit. 2. SERVICE MENU ITEMS With the SERVICE MENU,various settings (adjustments)can be made,and they are broadly classified in the following items of settings: •...
Page 18
AV-29WS3 SERVICE MENU SUB MENU 1. IF SERVICE MENU 1. IF 2. VC VCO (CW) ***** 3. DEF 4. VSM PRESET TOO HIGH 5. PRESET 6. A2NICAM 1. VCO ABOVE REFERENCE 7. PLUG & PLAY (ON) BELOW REFERENCE 2. DELAY POINT...
Page 19
AV-29WS3 ADJUSTMENTS B1 POWER SUPPLY Measuring Item Test point Adjustment part Description instrument Check of Signal B1 (pin 1) 1. Receive a black and white signal. generator GND (pin 5) 2. Connect a DC voltmeter between B1 and GND B1 POWER...
Page 20
AV-29WS3 VC (VIDEO/CHROMA) CIRCUIT ADJUSTMENTS The setting (adjustment) using the remote control unit is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
Page 21
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Signal 2. DRIVE (R) Notes: Adjustment of WHITE generator DRIVE (G) • Proceed to the following adjustment after having completed the ad- BALANCE DRIVE (B) justment of LOW LIGHT WHITE BALANCE.
Page 22
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Remote 5. COLOR [Method of adjustment without measuring instrument] Adjustment control unit Notes: • Proceed to the following adjustment after having completed the ad- COLOR-I justment of SUB CONT. • Set PICTURE MODE (VSM) to “BRIGHT”.
Page 23
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Adjustment Signal 6. TINT [Method of adjustment without measuring instrument] generator Notes: SUB TINT-I • Proceed to the following adjustment after having completed the ad- Remote justment of SUB CONT. control unit •...
Page 24
AV-29WS3 DEFLECTION CIRCUIT ADJUSTMENTS The setting (adjustment) using the remote control unit is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
Page 25
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Adjustment 2. VER. HEIGHT 9. Receive a PAL cross-hatch signal. Signal 10. Select 2. VER. HEIGHT with the MENU &/^ key. 13. V. ZOOM generator V. HEIGHT 11. Set the initial setting value of 2. VER. HEIGHT with the MENU */Tkey.
Page 26
AV-29WS3 Measuring Item Test point Adjustment part Description instrument 23. Select 7. EW-PIN with the MENU &/^ key. Adjustment 7. EW-PIN Signal 24. Set the initial setting value of 7. EW-PIN with the MENU */Tkey. generator SIDE PIN 25. Adjust 7. EW-PIN so that the first vertical lines at the left and right edges on the screen are straight.
Page 27
AV-29WS3 Measuring Item Test point Adjustment part Description instrument 32. Select 9. UP CORNER with the MENU &/^ key. Adjustment 9. UP CORNER Signal 10. DW CORNER 33. Set the initial setting value of 9. UP CORNER with the MENU generator */Tkey.
Page 28
AV-29WS3 [COMPRESS (16 : 9) : OFF, fv: 60Hz mode ] Measuring Item Test point Adjustment part Description instrument Adjustment Signal 1. VER. SLOPE 1. Receive a NTSC circle pattern signal of vertical frequency 60Hz. generator 2. Select 3. DEF from the SERVICE MENU.
Page 29
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Adjustment 2. VER. HEIGHT 9. Receive a NTSC cross-hatch signal. Signal 10. Select 2. VER. HEIGHT with the MENU &/^ key. 13. V. ZOOM generator V. HEIGHT 11. Set the initial setting value of 2. VER. HEIGHT with the MENU */Tkey.
Page 30
AV-29WS3 Measuring Item Test point Adjustment part Description instrument 23. Select 7. EW-PIN with the MENU &/^ key. Adjustment 7. EW-PIN Signal 24. Set the initial setting value of 7. EW-PIN with the MENU */Tkey. generator SIDE PIN 25. Adjust 7. EW-PIN so that the first vertical lines at the left and right edges on the screen are straight.
Page 31
AV-29WS3 Measuring Item Test point Adjustment part Description instrument 32. Select 9. UP CORNER with the MENU &/^ key. Adjustment 9. UP CORNER Signal 10. DW CORNER 33. Set the initial setting value of 9. UP CORNER with the MENU generator */Tkey.
Page 32
AV-29WS3 [COMPRESS (16 : 9) : ON, fv: 50Hz mode ] Measuring Item Test point Adjustment part Description instrument Signal 13. V. ZOOM 1. Receive a PAL cross-hatch signal of vertical frequency 50Hz. Adjustment generator 2. VER. HEIGHT 2. Select COMPRESS from the MENU and set COMPRESS to ON.
Page 33
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Adjustment 7. EW-PIN 13. Receive a PAL cross-hatch signal. Signal 14 Select 7. EW-PIN with the MENU &/^ key. generator 15. Set the initial setting value of 7. EW-PIN with the MENU */Tkey.
Page 34
AV-29WS3 [COMPRESS (16 : 9) : ON, fv: 60Hz mode ] Measuring Item Test point Adjustment part Description instrument Signal 13. V. ZOOM 1. Receive a NTSC cross-hatch signal of vertical frequency 60Hz. Adjustment generator 2. VER. HEIGHT 2. Select COMPRESS from the MENU and set COMPRESS to ON.
Page 35
AV-29WS3 Measuring Item Test point Adjustment part Description instrument Adjustment 7. EW-PIN 13. Receive a NTSC cross-hatch signal. Signal 14 Select 7. EW-PIN with the MENU &/^ key. generator 15. Set the initial setting value of 7. EW-PIN with the MENU */Tkey.
Page 36
AV-29WS3 [VIDEO - 2 SET : COMPONENT, fv: 50/60Hz mode] Measuring Item Test point Adjustment part Description instrument Adjustment 5. HOR. POSITION 1. Receive a PAL circle pattern signal to VIDEO-2 terminal. Signal 2. Select VIDEO-2 SET from the MENU and set VIDEO-2 SET to generator H.
Page 37
AV-29WS3 PRESET SETTING • Do not adjust 5. PRESET in the SERVICE MENU as it requires no adjustment. [SUB MENU 5. PRESET] Setting item Variable range Initial setting value PSNS IFLH AFCW 00/01/10/11 50 – 95 READ STATUS — —...
Page 38
AV-29WS3 PURITY ADJUSTMENT Note: The final adjustment of CONVERGENCE must be done after the FOCUS adjustment. (CONVERGENCE is changed by FOCUS adjustment.) When makes difference by FOCUS adjustment, should be WEDGE DEFLECTION reconfirming PURITY adjustment. YOKE 1. Demagnetize CRT with the demagnetizer.
Page 39
AV-29WS3 CONVERGENCE ADJUSTMENTS STATIC CONVERGENCE ADJUSTMENT 1. Input a crosshatch signal. (FRONT VIEW) 2. Using 4-pole convergence magnets, overlap the red and blue lines in the center of the screen (Fig. 4) and turn them to magenta (red/blue). 3. Using 6-pole convergence magnets, overlap the magenta(red/blue) and green lines in the centre of the screen and turn them to white.
Page 40
AV-29WS3 SELF-CHECK FUNCTIONS 1. Outline This model has self-check functions given below.When an abnormality has been detected,the SUB POWER is turned off and both ECO and ON TIMER LEDs flash to inform of the failure.An abnormality is detected by the signal input state of the control line connected to the microcomputer.
Page 42
VICTOR COMPANY OF JAPAN, LIMITED HOME AV NETWORK BUSINESS UNIT 12,3-chome,Moriya-cho,Kanagawa-ku,Yokohama,Kanagawa-prefecture,221-8528,Japan Printed in Japan AV29WS3M-H 0212 WPC...
Page 43
AV-29WS3 PARTS LIST CAUTION q The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the safety . q The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied .
Page 44
AV-29WS3 CONTENTS USING P.W. BOARD & REMOTE CONTROL UNIT ................. EXPLODED VIEW PARTS LIST -1 ......................EXPLODED VIEW -1 ..........................EXPLODED VIEW PARTS LIST -2 ......................EXPLODED VIEW -2 ..........................PRINTED WIRING BOARD PARTS LIST MAIN PW BOARD ASS’Y ............................. 46 CRT SOCKET PW BOARD ASS’Y ........................
AV-29WS3 USING P.W. BOARD & REMOTE CONTROL UNIT Model AV-29WS3 P.W.B ASS’Y MAIN PWB SCH-1107A-H2 CRT SOCKET PWB SCH-3005A-H2 FRONT CONTROL PWB SCH-8004A-H2 REMOTE CONTROL UNIT RM-C1010-1H EXPLODED VIEW PARTS LIST -1 ! Ref.No. Part No. Part Name Description Local...
AV-29WS3 EXPLODED VIEW PARTS LIST -2 ! Ref.No. Part No. Part Name Description Local ! V01 A68QCU257X75K PICTURE TUBE (ITC) Inc. DEF YOKE ! L01 QQW0150-001 DEG COIL ! T1551 QQH0139-001 Not including ANODE WIRE ASS’Y LC11061-001A-H CHASSIS BASE LC11062-001D-H...
AV-29WS3 EXPLODED VIEW -2 FRONT CABINET FRONT CONTROL PWB (2/2) SOCKET PWB MAIN PWB FRONT CONTROL PWB (1/2) T1551 <PICTURE TUBE (REAR SIDE)> No. 52081...
AV-29WS3 PRINTED WIRING BOARD PARTS LIST MAIN PW BOARD ASS’Y (SCH-1107A-H2) ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local RESISTOR RESISTOR ! R1529 R1001 NRSA63J-221X MG R 220¸ 1/16W QRZ9021-1R0 1¸...
Page 49
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local RESISTOR RESISTOR R1726 NRSA63J-472X MG R 4.7k¸ 1/16W R1880 NRSA63J-202X MG R 2k¸ 1/16W R1727 NRSA63J-104X MG R 100k¸ 1/16W R1881...
Page 50
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local CAPACITOR CAPACITOR C1308 NCB31HK-103X C CAP. 0.01µF 50V K C1641 QETN1HM-475Z E CAP. 4.7µF 50V M C1315 QFLC1HJ-473Z M CAP. 0.047µF...
Page 51
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local CAPACITOR COIL C1821 NCF31AZ-105X C CAP. 1µF 10V Z L1541 QQL244K-220Z COIL 22µH C1822 QETN1CM-477Z E CAP. 470µF 16V M L1561...
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local TRANSISTOR OTHERS Q1101 2SC5083/L-P/-T TRANSISTOR K1705 QQR1214-001Y FERRITE BEADS Q1102 UN2212-X DIGI. TRANSISTOR K1901 QQR1214-001Y FERRITE BEADS Q1103 UN2212-X DIGI. TRANSISTOR...
Page 53
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local RESISTOR RESISTOR R3123 QRE121J-152Y 1.5k¸ 1/2W R3263 NRSA63J-101X MG R 100¸ 1/16W R3124 NRSA63J-221X MG R 220¸ 1/16W R3264 NRSA63J-222X MG R 2.2k¸...
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local DIODE OTHERS D3118 1SS244-T2 SI. DIODE K3204 CE41492-001Z CHOKE COIL D3119 1SS244-T2 SI. DIODE K3205 QQR1113-001Z FERRITE BEADS D3120 1SS244-T2 SI. DIODE...
AV-29WS3 ! Symbol No. ! Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local COIL L8401 QQL244K-820Z COIL 82µH DIODE D8801 MA111-X SI. DIODE D8802 P1241-04 PHOTO CONDUCTOR D8803 SLR-342VR-T16 TRANSISTOR Q8481 2SC2412K/QR/-X TRANSISTOR Q8801...
AV-29WS3 PACKING PACKING PARTS LIST ! Ref.No. Part No. Part Name Description Local CP30967-004-H POLY BAG GG10044-043A-H P CASE GG10193-001C-H CUSHION ASSY RM-C1010-1H RC HAND UNIT CP30966-001-H POLY BAG LCT1170-001B-H INST BOOK QAM0054-001 CONVERSION PLUG LC30946-001A-H CRT PROTECTOR LC30947-002A-H CAUTION SHEET...
Page 58
AV-29WS3 SCHEMATIC DIAGRAMS COLOR TELEVISION BASIC CHASSIS AV-29WS3 CD-ROM No. SML200301 POWER MUTING SYSTEM CINEMA COLOUR SOUND SURROUND DISPLAY SENSOR MENU I/II TV/TEXT TV/VIDEO TIMER PICTURE MODE CHANNEL RETURN+ SCAN -/-- CHANNEL VOLUME TEXT REVEAL HOLD INDEX SIZE SUBPAGE STORE...
Page 59
AV-29WS3 AV-29WS3 STANDARD CIRCUIT DIAGRAM q NOTE ON USING CIRCUIT DIAGRAMS • 1. SAFETY Type No indication : Ceramic capacitor The components identified by the symbol and shading are : Mylar capacitor critical for safety. For continued safety replace safety critical : Metalized mylar capacitor components only with manufactures recommended parts.
Page 60
AV-29WS3 CONTENTS SEMICONDUCTOR SHAPES ..........................2-2 BLOCK DIAGRAM ................................2-3 CIRCUIT DIAGRAMS MAIN PWB CIRCUIT DIAGRAM (1/2) ..........................2-5 MAIN PWB CIRCUIT DIAGRAM (2/2) ..........................2-7 CRT SOCKET PWB CIRCUIT DIAGRAM ........................2-9 FRONT CONTROL PWB CIRCUIT DIAGRAM ......................2-11...
AV-29WS3 FRONT CONTROL PWB PATTERN FRONT CONTROL ( 1/2 ) FRONT FRONT CONTROL ( 2/2 ) C552 Y501 C505 Y502 D602 C554 C551 U.SOMKIAT 3.JUL'02 W052 CKF1681-BH1-1 \402/2\41 CN003 W051 MARK R815 R827 R811 R810 R809 R808 R807 R828 R831...
Page 69
VICTOR COMPANY OF JAPAN, LIMITED HOME AV NETWORK BUSINESS UNIT 12,3-chome,Moriya-cho,Kanagawa-ku,Yokohama,Kanagawa-prefecture,221-8528,Japan Printed in Japan AV29WS3M-H 0212 WPC...