Subscribe to Our Youtube Channel
Related Manuals for Fike 10-055-3-C
Summary of Contents for Fike 10-055-3-C
- Page 1 Expanded Enclosures Installation Guide THREE BAY TWO BAY EXPANDED ENCLOSURE EXPANDED ENCLOSURE 10-055-3-C CHEETAH / SHP 10-055-2-C CHEETAH / SHP 10-060-3-C SHARK 10-060-2-C SHARK Manual P/N: 06-185 Revision No: 1, 11/01...
- Page 3 The information contained in this manual is as accurate as currently possible. This manual is intended to be an aid to Fike authorized sales outlets, who have been trained in an approved manner by Fike, and the user who is a customer of the Fike authorized sales outlet. Fike does not warrant that this manual is technically correct, complete, or free from writing problems or that the Fike products referenced therein are free from minor flaws.
-
Page 5: Table Of Contents
FIKE CORPORATION TABLE OF CONTENTS Section Page 1.0 PREFACE..............................1 About This Manual ........................1 Product Support .........................1 Revision History .........................1 Terms Used in this Manual ......................1 Safety Notices ...........................2 2.0 PRODUCT OVERVIEW ..........................3 Product Description........................3 Listings and Approvals .......................3 Agency Standards and Compliance..................3-4 Related Documentation......................4... -
Page 7: 1.0 Preface
Manual. This manual is intended for the designer and installer. Before you refer to any section in this manual, and before you attempt to install or use the Fike electronic hardware, be sure to read the important User Information that follows this explanation. -
Page 8: Safety Notices
Always ground yourself with a proper wrist strap before handling the module(s). If the installer is grounded at all times, damage due to static discharge will not occur. If the module requires repair or return to Fike, it must be shipped in an anti-static bag. -
Page 9: Product Overview
PRODUCT OVERVIEW PRODUCT DESCRIPTION The Fike Expanded Enclosures, P/N 10-055-2-C (-3-C) and P/N 10-060-2-C (-3-C) provide two “standard” panel enclosure sizes for the Cheetah, Shark and SHP Control Systems. Additional hardware is also available to provide mounting for the Cheetah/VESDA HLI, VESDA LaserCompact, Addressable Modules, and Batteries. -
Page 10: Related Documentation
OVERVIEW FIKE CORPORATION The installer should also be familiar with the following documents and standards: UL 864 – Standard for Control Units for Fire Protective Signaling Systems UL 1481 – Power Supplies for Fire Protective Signaling Systems ULC – Standard CAN/ULC-S527-M87... -
Page 11: Equipment Products
Electrical knockouts are located on all sides for wire entry. 10-055-3-C / 10-060-3-C Where C = R (Red) G (Gray) The basic three-bay enclosure combination provides the main backbox and door for three bays of fire control system hardware. - Page 12 EQUIPMENT FIKE CORPORATION 10-059-P Cheetah Control System 10-057-P Shark Control System 10-058-P SHP Control System Where P = Power 1 = 120 VAC 2 = 240 VAC This system includes the control panel, mounting plate, and transformer. The AC terminal block is installed on the plate.
- Page 13 FIKE CORPORATION EQUIPMENT 10-2345 Optional Mounting Plate, Cheetah/VESDA High Level Interface (HLI) This kit provides a stainless steel mounting plate, mounting hardware, 10-2277 Cheetah/VESDA High Level Interface 10-2277 HLI (HLI) printed circuit board assembly, 02-3053 RS-232 cable, and Cheetah/VESDA interface manual. It is approximately 12”...
-
Page 14: Equipment/Products - Spare Parts
02-2842 #6-32, Nut and Washer kit 02-4035 #6-32, Screw and Washer kit 02-4956 Touch-Up Paint (Not available from Fike) Red-Sherwin Williams - #F63VXR9951-4343 Polane 2.8T Plus Polyurethane Enamel Gray-Sherwin Williams - #F63VXA9975 Polane T Plus Polyurethane Enamel Page 8 of 23 Expanded Enclosures Installation Guide U.L. -
Page 15: Enclosure Specifications
FIKE CORPORATION EQUIPMENT ENCLOSURE SPECIFICATIONS The Cheetah/SHP (3.3.1,3.3.3) and the Shark (3.3.2, 3.3.4) enclosures are identical except for the door’s display cutout. 3.3.1 Two Bay Cheetah / SHP Enclosure Mounting Methods: Surface - Using tear-drop openings in back of backbox Flush - Includes ½... - Page 16 EQUIPMENT FIKE CORPORATION 3.3.2 Two Bay Shark Enclosure Mounting Methods: Surface - Using tear-drop openings in back of backbox Flush - Includes ½ “ (1.27 cm) lip around backbox and removable door with full swing Weight: 21.5 lbs. (9.75 kg) empty Over-all Dimension: 15.25”...
- Page 17 FIKE CORPORATION EQUIPMENT 3.3.3 Three Bay Cheetah / SHP Enclosure Mounting Methods: Surface - Using tear-drop openings in back of backbox Flush - Includes ½ “ (1.27 cm) lip around backbox and removable door with full swing Weight: 26.5 lbs. (12.02 kg) empty Over-all Dimension: 15.25”...
- Page 18 EQUIPMENT FIKE CORPORATION 3.3.4 Three Bay Shark Enclosure Mounting Methods: Surface - Using tear-drop openings in back of backbox Flush - Includes ½ “ (1.27 cm) lip around backbox and removable door with full swing Weight: 26.5 lbs. (12.02 kg) empty Over-all Dimension: 15.25”...
- Page 19 FIKE CORPORATION EQUIPMENT 3.3.5 Mounting Plate Assemblies All mounting plate assemblies include hardware for mounting the plate to the back box. Also included is mounting hardware for installing electronic components. Reference Section 5.2 for mounting plate installation. 12.94 11.00 1.44 •...
- Page 20 EQUIPMENT FIKE CORPORATION 12.00 11.00 • Plate Assembly, Addressable Modules P/N: 10-2347 *One plate will support six modules 1. Stainless Steel Plate 0.50 TYP. 2. 12 Standoffs, M/F, #6-32 x 1.5” 3. 12 Standoffs, F/F, #6-32 x 1” 13.50 10.00 4.
-
Page 21: Design
FIKE CORPORATION DESIGN DESIGN The importance of proper design for fire alarm and suppression signaling systems cannot be overemphasized. Refer to the appropriate control system manual, local codes and requirements, and the requirements of national fire codes and standards as listed in Section 2.3 of this manual. -
Page 23: Installation
Always ground yourself with a proper wrist strap before handling modules. If the installer is grounded at all times, damage due to static discharge will not occur. If a module requires repair or return to Fike, it must be shipped in an anti-static bag. -
Page 24: Install Mounting Plates
INSTALLATION FIKE CORPORATION INSTALL MOUNTING PLATES The enclosure will be shipped with various hardware components depending on the optional modules and the mounting plates ordered with the shipment. Mounting plates are shipped with mounting hardware. Reference Section 3.0 for specific hardware information. Mounting Plates are to be inserted over the press-studs extending out from the backbox and secured with lock washers and hex nuts. -
Page 25: Install Miscellaneous Labeling
Depending on the control panel ordered, the appropriate labeling kit will be shipped. Cheetah / SHP enclosure will have the Fike logo silk-screened on the door. Shark enclosure will come with a Shark label. Install the Shark Control Panel label on the lower right corner of the enclosure front door. -
Page 26: Install Internal Electronic Assemblies
INSTALLATION FIKE CORPORATION INSTALL INTERNAL ELECTRONIC ASSEMBLIES Wear grounding strap while installing internal electronic assemblies. Reference the appropriate control panel manual for proper installation procedure of control equipment. 5.4.1 Control Systems 10-059-1 (-2) – Cheetah Control System 10-057-1 (-2) – Shark Control System 10-058-1 (-2) –... - Page 27 FIKE CORPORATION INSTALLATION Detail B Mounting Plate Shark Control Board #6-32 Hex Nut w/ Washer Typ. 8 Plcs. Shark Detector Assembly Detail C Enclosure with door Shark Control Board Ground Strap (10 AWG) p/n: 02-4992 Hex Nut w/ Star Washer 4 Plcs.
- Page 28 INSTALLATION FIKE CORPORATION 5.4.2 Optional Mounting Plate Assemblies These plate assemblies provide an easy way of attaching control boards, modules or batteries to the expanded enclosure. Refer to Section 3.1 for product information. Mounting hardware for the plate as well as the electronic component the plate supports is included in the plate assembly. All plates are mounted flush against the back box to the 6-32 threaded press stud.
- Page 29 FIKE CORPORATION INSTALLATION 10-2347 - Addressable Module Mounting Plate Attach mounting plate to enclosure using the hex nuts and washers provided. When attaching modules (sold separately) use 1 ½” standoffs on one side of module and the 1” standoff with the ½”...
- Page 30 704 South 10 Street P.O. Box 610 Blue Springs, Missouri 64013 U.S.A. (816) 229-3405 Fax: (816) 229-5082 http://www.fike.com...
Need help?
Do you have a question about the 10-055-3-C and is the answer not in the manual?
Questions and answers