Table of Contents
Advertisement
Installation tips
Gas connection
HOT PARTS
for the convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed "Adaptation to different gas
types". In the case of connection to liquid gas, by
tank, use pressure regulators that conform to the
regulation in force. The gas supply must be
connected to the left of the appliance. Be sure that
the hose does not pass through the rear of the
cooker touching hot parts.
Make sure the supply pressure conforms with the
values shown in the table entitled "Caracteristics of
the burners and nozzles".
When the cooker is installed between
When the cooker is installed between
When the cooker is installed between
When the cooker is installed between
When the cooker is installed between
cabinets (recessed), the gas connection
cabinets (recessed), the gas connection
cabinets (recessed), the gas connection
cabinets (recessed), the gas connection
cabinets (recessed), the gas connection
must be effected by an approved flexible
must be effected by an approved flexible
must be effected by an approved flexible
must be effected by an approved flexible
must be effected by an approved flexible
hose with bayonet fitting
hose with bayonet fitting
hose with bayonet fitting
hose with bayonet fitting
hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
f i t t i n g .
f i t t i n g .
f i t t i n g .
f i t t i n g .
f i t t i n g .
The cooker should
be connected to the
gas-supply by a
gas safe registered
installer. During
installation of this
product it is
essential to fit an
approved gas tap to
isolate the supply
from the appliance
! This procedure must be performed by a qualified
technician who has been authorised by the
manufacturer.
Connecting the gas supply
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
•
the hose must never be at any point in its
lenght in contact with the "hot" parts
of the
cooker;
•
the hose must never be longer than 1,5
metre;
•
the hose must not be subject to any tension
or torsional stress and it must not
have any
curves or bottlenecks;
•
the hose must be easy to inspect along its
entire length to check its condition;
•
the hose must always be in good condition,
never attempt to repair.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of
gas with respect to the gas for which it was
produced (indicated on the label attached to the lid),
follow these steps:
a) a) a) a) a) replace the hose holder mounted on the
appliance with that supplied in the bag of "cooker
accessories".
b) b) b) b) b) Replacing the burner nozzles on the hob:
•remove the grids and slide the burners from their
housings;
• unscrew the nozzles
using a 7 mm socket
spanner, and replace
them with nozzles for
the new type of gas
(see table 1 "Burner and
nozzle characteristics").
•replace all the
components by
repeating the steps in
reverse order.
EN
excessively narrow
9
Hide quick links:
Advertisement
Table of Contents
