saro ZITA CB-35A Instruction Manual

Built-in induction cooking plate

Advertisement

General notes
Carefully read these instruction manual through as they contain important information.
It is advisable to keep the instruction manual in a place where you have them always
ready to hand. Should you pass the induction cooking plate on to a third party, this
instruction manual must be handed on.
As soon as you have unpacked the induction cooker, check whether everything is in a
faultless condition. Should anything be damaged, do not connect the appliance as such,
but inform your dealer.
The induction cooker must only be used for the intended purpose. Improper use can
cause damages and lead to the loss of the warranty.
Before you connect the induction cooker, make sure that the type of current stated on the
identification plate corresponds with your mains supply.
In the case of fault and/or malfunction, pull the plug out of the socket and inform your
dealer. He will carry out the repair with original spare parts.
Please observe the local regulations concerning accident prevention and disposal.
The manufacturer/dealer cannot be made responsible for damages which arise through
not observing these operating instructions. Apart from this, if these instructions are not
observed, oven safety is no longer guaranteed.
Safety notes
1. Do not touch the cooker and the plug with wet hands.
2. Do not plug into a socket where several other appliances are plugged in.
3. Do not pull the plug out of the socket by the cable.
4. The cable must not hang over table edges and/or sharp edges. It also must not come into
contact with the hot appliance surface or with water.
5. Check regularly the cable. If it is damaged, it must be exchanged by a qualified specialist.
6. Use only compatible induction cookware with diameter of 12 to 26 cm.
7. Make sure that the following things are not near to the cooker:
inflammable articles, as curtain etc.
gas or electric ovens
other sources of warmth
open fire
water armatures
devices or objects, which react sensitively to magnetic fields (e.g. radios, TV, cassette
recorders etc.)
8. Do not leave the oven unattended while it is in use. Children are not able to realise
dangers when handling electronic appliances.
9. Do not place any metal objects on the induction cooker.
Instruction Manual
Built-In Induction Cooking Plate
Model ZITA CB-35A
Order no. 301-1050
www.saro.de
page 1 of 5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZITA CB-35A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for saro ZITA CB-35A

  • Page 1 Instruction Manual Built-In Induction Cooking Plate Model ZITA CB-35A Order no. 301-1050 General notes • Carefully read these instruction manual through as they contain important information. • It is advisable to keep the instruction manual in a place where you have them always ready to hand.
  • Page 2 Instruction Manual Built-In Induction Cooking Plate Model ZITA Continuation „Safety notes“ 10. Do not place any empty containers on the induction cooker. 11. Do not touch the hot surface of the glass field. 12. Before each cleaning session, allow the cooker to cool down and pull the plug out of the socket.
  • Page 3: Cause Of Overheating

    Instruction Manual Built-In Induction Cooking Plate Model ZITA Continuation „Installation and start-up“ • Place induction cookware (diameter 12 to 26 cm) with the food to be cooked in the centre of the hotplate. Do not place the pot or the pan without food on the cooker. •...
  • Page 4: Control Panel

    Instruction Manual Built-In Induction Cooking Plate Model ZITA CONTROL PANEL CLEANING • Clean after each use. • Allow the cooker to cool down. • Switch off the device and disconnect the power plug from the socket. • Wipe down the cooker using a dish washing agent and a damp cloth and dry properly. •...
  • Page 5 Instruction Manual Built-In Induction Cooking Plate Model ZITA 1. Induction Heating Zone 3,5 kW 2. Component casing 3. Air-intake 4. Air-outlet 5. Remote Control Installation-Slots 1. Control box cut out:: 87 mm (H) x 225 (W) 2. Air in-take cut out: 50 mm (H) x 355 (W) 3.

Table of Contents