Montigo Proflame 2 Upgrade Kit RX 100 NG/LP Installation Manual
Montigo Proflame 2 Upgrade Kit RX 100 NG/LP Installation Manual

Montigo Proflame 2 Upgrade Kit RX 100 NG/LP Installation Manual

Advertisement

Quick Links

Proflame 2 Upgrade Kit RX 100 NG/LP
Upgrade Kit NG/LP Proflame 2 (Full Load with
Remote Upgrade Kit)
This kit is for use with the following models:
H Series
L Series
Ensure that all power to the appliance is off at the electrical breaker or fuse
before beginning installation. Ensure gas is turned off at the shutoff valve before
beginning installation.
 Installation and service must be performed by a qualified installer, service agency or
Page 1
®
C
US
CAUTION
Warning: If the information in these instructions is not followed
exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
What To Do If You Smell Gas:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
If you cannot reach your gas supplier, call the fire department.
the gas supplier.
The installation of this kit must be done by a qualified and
certified gas appliance installer.
Check local codes and read all instructions prior to instal-
lation.
When installing the replace - gas lines, ttings, accesso-
ries or any other objects cannot impede the proper
movement of the door buckles.
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
WARNING
WARNING
information go to www.P65warnings.ca.gov
XT0012 - 151127.1
Upgrade Kit

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Proflame 2 Upgrade Kit RX 100 NG/LP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Montigo Proflame 2 Upgrade Kit RX 100 NG/LP

  • Page 1 Upgrade Kit Proflame 2 Upgrade Kit RX 100 NG/LP Upgrade Kit NG/LP Proflame 2 (Full Load with Remote Upgrade Kit) This kit is for use with the following models: H Series L Series The installation of this kit must be done by a qualified and ...
  • Page 2: Table Of Contents

    A. Disconnecting Wall Switch Harness: This upgrade kit contains the necessary components for field B. Stepper Motor Installation: upgrade of an approved Montigo fireplace from Proflame 2 standard C. Main ON/OFF Switch Installation: control system to Full Load with remote.
  • Page 3: Disconnecting Wall Switch Harness

    Installation A. Disconnecting Wall Switch Harness: Ensure the prefitted rubber gasket is properly positioned (Figure Remove valve blind and glass door. 8 - D). Otherwise, fit the gasket as shown. Disconnect the wall switch harness from X4 Control Module and discard. X4 Control Module Figure 8 SIT Instructions Figure...
  • Page 4: Main On/Off Switch Installation

    Installation Figure 14 C. Main ON/OFF Switch Installation: Attach switch to bracket. Position the Main ON/OFF Switch bracket on the right leg of the firebox as shown in Figure 12 and Figure 13. Use the two supplied selftapping screws to attach the bracket. See Figure 13.
  • Page 5: Battery Holder Installation

    Installation D. Battery Holder Installation: E. Stepper Motor and ON/OFF Switch: Secure the battery holder to the fireplace floor using the supplied velcro strips. See Figure 16. Connect the Manual ON/OFF switch to X4 of the control Note: The velcro strips act as an electrical isolation, do not attach module.
  • Page 6: Operation With Backup Battery

    Installation F. Operation with Backup Battery: G. Operation with MAIN Power: Install the four supplied AA batteries to the battery holder. Remove the four batteries from the battery holder CAUTION: Please note battery orientation while installing them. Plug the Control Module Power cord to the PPO box. See Figure 3.
  • Page 7: Cpi / Ipi Jumper Cable Installation

    Installation CPI [Continuous Pilot Ignition] / IPI [Intermittent Pilot Igni- Installing the CPI Jumper Cable tion] Jumper Cable Installation (only available for SIT 1). Access the controller (refer to the installation and Electronic Ignition Systems) maintenance manual for your model). “Why use CPI mode”? CPI means “Continuous Pilot Ignition”...
  • Page 8 Proflame 2 Upgrade Kit RX 100 NG/LP XT0012 - 151127.1...

Table of Contents