Subscribe to Our Youtube Channel
Related Manuals for Oceanic Vision Series
Summary of Contents for Oceanic Vision Series
- Page 1 S a u n a & S t e a m Vision Sauna Manual 14.7.18 Wall Hung Heater Version (Covers all models) Oceanic Ltd, Pountney Street, Wolverhampton, WV2 4HX Phone: 01902 450 550 sales@oceanic-saunas.co.uk www.oceanic-saunas.co.uk...
-
Page 2: Table Of Contents
17. External Trim (Fix in this order) ....... . 17 Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... -
Page 3: Introduction
Vision Sauna Manual Introduction Welcome to the instruction manual for the Oceanic Saunas Vision Range. This guide is meant to be used alongside a “Part List” which has specific information for the cabin you have been supplied. Please take time to familiorize youself with both the steps in the manual and the specific layout of benches and panels for the cabin your are building before making a start on assembly. -
Page 4: Step 1 Base
Countersink drill 4 holes evenly down the panel. iii. Fix from the back panel into the end of the side panel using 80mm screws. iv. The panels simply just sit onto the base, don’t fix down. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... -
Page 5: Wooden To Glass Panel Joint
There is a 50x50 fixing column supplied, fix this to edge of the glass panel using 4 x 60mm screws. Again do not overtighten the screws and pilot and countersink holes. Correct Depth Too Deep! Column Glass Frame Glass Panel Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... -
Page 6: Glass Panels
The door frame doesn’t have a channel on the external face so only fit the brackets to the internal join. ii. The door must be installed opening outwards. You can hinge the door from the left or right hinge by just rotating the frame 180 degrees. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... -
Page 7: Roof
Then measure and cut the trunking along the one or two edges that you require, if you mitre the trunking the cable will run around the corner perfectly without any other holes or notches being made. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... -
Page 8: Benches
50mm double round trim and corner mould with the concave front. We don’t recommend that you add these until the cornice and skirt is on first. We think this gives the best asthetic look. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... - Page 9 Fix the guard together using 30mm screws as shown in the two below image. iii. Chisel off the dowels, don’t chisel level ii. Hammer the dowels into the holes to cover the chisel about 2mm proud. screws. iv. Sand the dowels level. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
- Page 10 Fix the guard with 4 x 30mm screws. Plug, chisel and sand. vii. Drop the heater onto the mounting screw vi. Fix two 30mm screws at the positions shown to then secure using 2 x 30mm screws. hang the heater. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
-
Page 11: Internal Trim (Fix In This Order)
Up to 1800 mm with 1 extra support 3 x 12.5 stones people Before commencing the construction of the benches find the specification sheet for the sauna you are building. This will give detail of the correct quantities and positions of timbers and fixings. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... - Page 12 Use small pieces of corner mould as 19mm spaces. scrap timber square corner scrap timber bench slat 19mm corner work bench mould spacer Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
- Page 13 19mm corner under frame mould spacer mould spacer iv. Add the cross members, two are positioned 100mm from the ends, the third is centred, a dimension for A can be found on your parts list. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
- Page 14 Use the 30mm screws provided to fix down through the cross members into the slats. vii. If your parts list shows you have a bench leg, add this now as shown. Use 6x 40mm Screws. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
- Page 15 Vision Sauna Manual viii. Screw the benches onto the wall rails using 2 x 30mm screws and 2 x 30mm washers. ix. Fix L Benches together uising 2 x 50mm screws and 2 x 30mm washers. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
-
Page 16: Back Rests
For the remaining fixing positioned measure between the keyways (dimension A) vii. We recommend a height of around 250mm off the bench so 375mm for the screws will give you this. viii. Pilot with 3mm drill and fix 30mm screrws where needed. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... - Page 17 Remove the self adhesive tape and fix the LED into the wooden track. viii. Fix the assembled LED unit to the underside of the backrest timbers using the nail gun or use a hammer. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
- Page 18 Take the back rest off and drill a 12 mm hole for the wire. xi. Route the wire from the roof or control box location through the wall. xii. Connect up and mount the back rest back on the wall. Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
- Page 19 12V extension lead connector 240V Mains supply 12v transformer connector block 12v downlight 12v downlight DIagram 3 - Triple Downlight 240V Mains supply 12v transformer connector block 12v downlight 12v downlight 12v transformer 12v downlight Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
-
Page 20: External Trim (Fix In This Order)
Front corner facia (75mm double round) iii. Internal door frame Trim External trim iv. Overlap (50mm double round) v. Door trim (44mm double round) vi. Door trim (26mm double round) External door trim Internal door trim Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk... - Page 21 Ensure the cross lengths aligned equally beneath the length of the mat as shown in pink in the diagram below. v. Fix with glue and 30mm screws from the underside. (Pilot drill screw holes with 4mm countersink) Oceanic Saunas 01902 450 550 sales@oceanic-saunas.co.uk...
Need help?
Do you have a question about the Vision Series and is the answer not in the manual?
Questions and answers