Assembly And Adjustments - DeWalt DWE6005 Series Original Instructions Manual

Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 26 , which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/off switch
1
Motor unit
2
Depth adjustment ring
3
Micro adjustment scale
4
Groove pins
5
Spindle lock button
6
LED lights
7
Spindle
8
Collet
9
Collet nut
10
Cutter bit (not included)
11
Base
12
Sub-base
13
Sub-base screws
14
Quick release tabs
15
Locking lever
16
Locking lever adjustment screw
17
Guide slot
18
Straight edge guide
19
Roller bearing guide
20
Guide screw
21
Cutter bit shaft
22
Dust extraction adaptor
23
Finger screws
24
Dust exhaust port
25
Intended Use
Your D WALT DWE6005 Laminate Trimmer is a small base high-
e
precision power tool designed for professional trimming of
wood and plastic laminates.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This laminate trimmer is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Inserting the Motor into the Base (Fig. A, C)
1. Open the locking lever 16
2. If the depth adjustment ring
the ring onto the motor until the ring is about halfway
3
between the top and bottom of the motor. Insert the
motor into the base by aligning the groove in the back of
the motor unit with the groove pins
the motor down until the depth adjustment ring snaps
into place.
3. Adjust the depth of cut by turning the depth adjustment
ring. Refer to Depth of Cut Adjusment.
4. Close the locking lever 16
achieved. For information on setting the cutting depth,
Refer to Depth of Cut Adjusment.
Locking Lever Adjustment (Fig. A)
Excessive force should not be used to clamp the locking lever
16 . Using excessive force may damage the base.
When the locking lever is clamped, the motor should not move
in the base.
Adjustment is needed if the locking lever will not clamp without
excessive force or if the motor moves in the base after clamping.
Adjusting the Locking Lever's Clamping Force
1. Open the locking lever
16
2. Using a 2 mm hex wrench turn locking lever adjustment
screw 17 in small increments. Turning the screw clockwise
tightens the lever, while turning the screw counterclockwise
loosens the lever.
Motor Quick Release (Fig. D)
1. Open the locking lever
16
2. Grasp the motor unit with one hand, depressing both quick
release tabs 15 .
3. With the other hand, grasp the base and pull motor from
the base.
English
on the base.
3 is not on the motor, thread
5 on the base. Slide
when the desired depth is
.
on the base.
7