Residual Risks; Electrical Safety; Package Contents - DeWalt DWE6005 Series Original Instructions Manual

English
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional Safety Rules for Trimmers
• Hold power tool by insulated gripping surfaces, because
the cutter may contact its own cord. Cutting a "live" witre
may make exposed metal parts of the power tool "live" and
shock the operator.
• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holidng the
work by your hand or against the body leaves it unstable and
may lead to loss of control.
• Never run the motor unit when it is not inserted in one of
the router bases. The motor is not designed to be handheld.
• Always use straight-cutters, rabbet-cutters, profile cutters,
slotter cutters or grooved knives with a shank diameter of
6 – 6.35 (1/4") mm which corresponds to the size of the collet
in your tool.
• Always use cutters suitable for a speed of 35000 min
marked accordingly.

WARNING: Never use cutters with a diameter exceeding
the maximum diameter indicated in the technical data.
• For slotter cutters, the maximum shank diameter MUST be
6.35 mm and the maximum diameter MUST be 25.4 mm.
For grooved knives, the maximum shank diameter MUST be
•
6.35 mm, the maximum diameter MUST be 25.4 mm and the
maximum cutting width MUST be 4 mm.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
6

Residual Risks

In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D
with EN60745; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
and
-1

Package Contents

The package contains:
1 Motor unit
1 Collet 6 mm (6.35 / 1/4")
1 Wrench # 17 mm
1 Straight edge guide
1 Roller bearing guider
1 Dust Extraction Adaptor
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
WALT tool is double insulated in accordance
e
WALT
e
; the
2