Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for B&B ARMR 4X0E Series
Summary of Contents for B&B ARMR 4X0E Series
- Page 1 MODEL 4X0E SERIES SLIDING GATE VEHICLE BARRIER INSTALLATION MANUAL B&B ARMR Headquarters & Tech Support: 5900 S Lake Forest Dr Suite 230 McKinney, TX 75070 Phone: (800) 367-0387 Fax: (972) 385-9887 E-mail: info@bb-armr.com techsupport@bb-armr.com www.bb-armr.com MADE IN THE USA...
-
Page 2: Welcome
Installation and Operations Manual — Model 400E Series Your safety is extremely important to us. If you have any questions or are in doubt about any aspect of the equipment, please contact us. INTRODUCTION Welcome! Congratulations on your purchase of a B&B ARMR vehicle barrier. In addition to providing detailed operating instructions, this manual describes how to install, maintain, and troubleshoot your vehicle barrier. -
Page 3: How To Contact Us
Installation and Operations Manual — Model 400E Series Engage only trained and experienced staff to install, operate, and maintain the equipment. Ensure that all repairs are performed correctly, using properly trained staff and the right tools and equipment. How to Contact Us If you have any questions or experience any problems with your vehicle barrier—or if we can help you with any other facility security issues—please contact us directly at: HQ/Tech Support:... -
Page 4: Table Of Contents
Installation and Operations Manual — Model 400E Series Table of Contents INTRODUCTION ............................iv Welcome! ..............................iv Safety ................................ iv How to Contact Us ........................... v System Installation Record ........................v 1. ORIENTATION ............................6 Overview ............................6 2. INSTALLATION ............................9 Preliminary Considerations ...................... - Page 5 Installation and Operations Manual — Model 400E Series Manual operation of the gate can be performed by lowering drive assembly, disengaging actuator from lock pins (Model 450 Only) and manually pushing the gate. An optional manual over ride system can be purchased at the time of order to allow gate opening and closing without disengaging drive assembly.
- Page 6 Installation and Operations Manual — Model 400E Series 1.1.2 Drive Stanchion The drive stanchion supports the gate with the four main drive wheels and allows the drive unit to mesh with the rack located on the underside of the gate beam. Figure 2 Model 4x0E Drive Stanchion Figure 3 Drive Unit B&B ARMR...
-
Page 7: Installation
Installation and Operations Manual — Model 400E Series 1.1.3 Receiver Stanchion The receiver stanchion captures (and locks in model 450) the end of the gate when the gate is fully closed. The Model 450 has a pair of two inch diameter stainless steel pins that are electrically actuated to lock the gate closed. -
Page 8: Typical Installation Of The Main And Receiver Stanchions
Installation and Operations Manual — Model 400E Series 1. Inspect the site and verify there are no underground utilities or overhead wires or obstructions in the excavation area. 2. Make sure that there is adequate free area adjacent to the motor stanchion's installation location so that the vehicle barrier gate can be slid onto the stanchion after the stanchion is cemented in place. -
Page 9: Installing The Gate And Motor Components
Installation and Operations Manual — Model 400E Series 2.2.7 Make the final concrete pour, again making sure the axle height does not change and remain level and plumb. Remove any concrete that might have splattered inside the exposed conduits. 2.2.8 After the concrete has set, install the roller wheels, collars and nuts onto the axles if not previously installed. -
Page 10: Control System Installation
Installation and Operations Manual — Model 400E Series Figure 5 Limit Switch Mounting 2.4.6 Bolt the limit switch plates so they engage the limit switches' lever arms. The plate must be located so that both limit switches are hit in the correct sequence. - Page 11 Installation and Operations Manual — Model 400E Series Description Terminal Block OPEN I1 CLOSE I2 LOCK PIN UP (450) I3 CLOSED LIMIT A I4 OPEN LIMIT A I5 SAFETY DEVICES (ALL) I6 STOP (NORMALLY CLOSED) I7 ECO I9 ECO RESET I10 CLOSED LIMIT B I11 OPEN LIMIT B I12 LOCK PIN DOWN (450) I13...
- Page 12 Installation and Operations Manual — Model 400E Series Before engaging the pinion with the rack, verify that the limit switches are mounted and wired correctly. Failure to do so could cause severe damage or injury. 3.3.4 Test CLOSE operation: Verify gate is positioned between limit switches and does not block locking pins (Model 450 only).
-
Page 13: Operational Test
Installation and Operations Manual — Model 400E Series Figure 6 End Plates 3.4 Operational Test 3.4.1 Give the gate an OPEN command. The locking pin will raise (Model 450), and the motor will accelerate and run to move the gate open. The first limit switch will begin the speed reduction of the motor. - Page 14 Installation and Operations Manual — Model 400E Series If the system you are operating is equipped with the manual override drive system the following is done to move the gate. Your safety is extremely important to us. Be sure to ...
- Page 15 Installation and Operations Manual — Model 400E Series B&B ARMR A Division of B&B Roadway and Security Solutions 0400E-9001 Rev J...
- Page 16 Installation and Operations Manual — Model 400E Series Drive Stanchion Manual Drive Procedure Serious injury may occur if electrical power resumes during this procedure. Do not alter or defeat safety Proximity Lockout Sensor (6). The Proximity Lockout Sensor is design to prevent accidental operation of the motor if power resumes during the use of the Manual Override Tool.
-
Page 17: Troubleshooting
Installation and Operations Manual — Model 400E Series After any major repairs, review the installation setup instructions before returning the barrier to service 5. TROUBLESHOOTING The table below provides guidance on identifying and correcting issues with your Model 400 Series vehicle barrier. If you encounter problems that you cannot fix, contact B&B ARMR and we will gladly work with you to correct them. -
Page 18: Reference Drawings
Installation and Operations Manual — Model 400E Series 6. REFERENCE DRAWINGS The following drawings are provided for reference only. For job specific drawings and details please refer to the Submittal Documentation specific to the job. For replacement components and parts breakdown, please contact B&B ARMR tech support. - Page 19 Installation and Operations Manual — Model 400E Series B&B ARMR A Division of B&B Roadway and Security Solutions 0400E-9001 Rev J...
- Page 20 Installation and Operations Manual — Model 400E Series B&B ARMR A Division of B&B Roadway and Security Solutions 0400E-9001 Rev J...
- Page 21 Installation and Operations Manual — Model 400E Series B&B ARMR A Division of B&B Roadway and Security Solutions 0400E-9001 Rev J...
- Page 22 Installation and Operations Manual — Model 400E Series B&B ARMR A Division of B&B Roadway and Security Solutions 0400E-9001 Rev J...
- Page 23 Installation and Operations Manual — Model 400E Series TYPICAL ELECTRICAL (450E SHOWN) B&B ARMR A Division of B&B Roadway and Security Solutions 0400E-9001 Rev J...
-
Page 24: Warranty
Installation and Operations Manual — Model 400E Series 7. WARRANTY BBRSS warranties for a period of one (1) year FOB manufacturing facility, unless otherwise specified by BBRSS in writing, from defects due to faulty material or workmanship. Damage due to handling during shipment and installation are not covered under warranty.