H3C S9500 Series Command Manual
Routing switches system maintenance and debugging
Hide thumbs
Also See for S9500 Series:
- Command manual (1842 pages) ,
- Operation manual (1504 pages) ,
- Operating manual (76 pages)
Table of Contents
Advertisement
Quick Links
Command Manual - System Maintenance and Debugging
H3C S9500 Series Routing Switches
Chapter 1 System Maintenance and Debugging Commands ................................................... 1-1
1.1 Basic System Configuration and Management Commands.............................................. 1-1
1.1.1 clock datetime ......................................................................................................... 1-1
1.1.2 clock summer-time .................................................................................................. 1-1
1.1.3 clock timezone......................................................................................................... 1-3
1.1.4 quick-ping enable .................................................................................................... 1-3
1.1.5 sysname .................................................................................................................. 1-4
1.2 Querying System Status and Configuring Agent Information............................................ 1-5
1.2.1 display clock ............................................................................................................ 1-5
1.2.2 display debugging ................................................................................................... 1-6
1.2.3 display device manuinfo.......................................................................................... 1-6
1.2.4 display fiber-module ................................................................................................ 1-7
1.2.5 display users ........................................................................................................... 1-9
1.2.6 display version....................................................................................................... 1-10
1.3 System Debugging Commands ....................................................................................... 1-11
1.3.1 debugging.............................................................................................................. 1-11
1.3.2 display diagnostic-information............................................................................... 1-12
1.4 Network Connection Test Commands ............................................................................. 1-14
1.4.1 ping........................................................................................................................ 1-14
1.4.2 pingmac................................................................................................................. 1-16
1.4.3 tracert .................................................................................................................... 1-17
1.4.4 tracemac enable.................................................................................................... 1-19
1.4.5 tracemac................................................................................................................ 1-20
1.5 Command Line Parser Cache Function Commands ....................................................... 1-21
1.5.1 parser cache.......................................................................................................... 1-21
1.5.2 display parser statistic........................................................................................... 1-21
Table of Contents
i
Table of Contents
Advertisement
Table of Contents
Related Manuals for H3C S9500 Series
Summary of Contents for H3C S9500 Series
-
Page 1: Table Of Contents
Command Manual – System Maintenance and Debugging H3C S9500 Series Routing Switches Table of Contents Table of Contents Chapter 1 System Maintenance and Debugging Commands ........... 1-1 1.1 Basic System Configuration and Management Commands..........1-1 1.1.1 clock datetime ......................1-1 1.1.2 clock summer-time .................... -
Page 2: Chapter 1 System Maintenance And Debugging Commands
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Chapter 1 System Maintenance and Debugging Commands 1.1 Basic System Configuration and Management Commands 1.1.1 clock datetime Syntax clock datetime HH:MM:SS YYYY/MM/DD... - Page 3 # Set the summer time for z2 that starts at 06:00:00 on 08/06/2002 and ends at 06:00:00 on 01/09/2002 with the time adding 1 hour. <H3C> clock summer-time z2 one-off 06:00:00 2002/06/08 06:00:00 2002/09/01 01:00:00 # Set the summer time for z2 that starts at 06:00:00 on 08/06 and ends at 06:00:00 on 01/09 in each year from 2002 on with the time adding 1 hour.
-
Page 4: Clock Timezone
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands 1.1.3 clock timezone Syntax clock timezone zone-name { add | minus } HH:MM:SS undo clock timezone View User view Parameters zone-name: Name of the time zone, which is a character with the length ranging from 1 to 32. -
Page 5: Sysname
Use the sysname command to configure the system name of the switch. Changing the hostname name of the switch will affect the prompt of command line interface. For example, if the system name of the switch is H3C, and the prompt in user view is <H3C>. -
Page 6: Querying System Status And Configuring Agent Information
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands [H3CLANSwitch] 1.2 Querying System Status and Configuring Agent Information 1.2.1 display clock Syntax display clock View Any view Parameters None Description Use the display clock command to display the system date and time information, so that you make timely changes if the system time is incorrect. -
Page 7: Display Debugging
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands 1.2.2 display debugging Syntax display debugging [ interface interface-type interface-number ] [ module-name ] View Any view Parameters interface-type: Interface type supported by the switch, including Ethernet, GigabitEthernet, AUX, and VLAN-interface. -
Page 8: Display Fiber-Module
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Examples # Display the manufacturing information of all cards. <H3C> display device manuinfo slot 0 DEVICE_NAME : LSBM1GP12B DEVICE_SERIAL_NUMBER : NONE... - Page 9 Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Description Use the display fiber-module command to display the information of the optical modules connected with all the optical interfaces in position on the current shelf,...
-
Page 10: Display Users
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Field Description WaveLength Wave length The transmission distance of X-um sized fiber is Y Length for X um: Y km/m km/m... -
Page 11: Display Version
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Delay Type Ipaddress Username CON 0 00:00:00 129 AUX 0 + 130 VTY 0 00:00:16 192.168.1.253 131 VTY 1 132 VTY 2... -
Page 12: System Debugging Commands
Comware software, Version 3.10, Feature 1631 Copyright(c) 2004-2007 Hangzhou H3C Technologies Co., Ltd. All rights reserved. H3C S9505 uptime is 0 week, 2 days, 4 hours, 19 minutes LSB1SRP1N6 1: uptime is 0 week,2 days,4 hours,19 minutes H3C S9500 with 1 MPC755 Processor... -
Page 13: Display Diagnostic-Information
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands module-name: Module name. debugging-option: Debugging option. Description Use the debugging command to enable the system debugging. Use the undo debugging command to disable the system debugging. - Page 14 H3C S9505 Product Version S9500-CMW310-F1631(EI) Copyright(c) 2004-2007 Hangzhou H3C Technologies Co., Ltd. All rights reserved. H3C S9505 uptime is 0 week, 2 days, 4 hours, 46 minutes This device is H3C S9505E LSB1SRP1N6 1: uptime is 0 week,2 days,4 hours,46 minutes...
-
Page 15: Network Connection Test Commands
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands CPLD Version Software Version : S9500-CMW310-F1631 CPUCard PCB Ver REV.0 CPLD Ver SubCard PCB Ver Ver.A CPLD Ver NONE SubCard PCB Ver Ver.A... - Page 16 Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands -n: Specifies that the host argument is used as the IP address, without domain name resolution performed. By default, host is taken as the IP address, and if host is not an IP address, domain name resolution will be performed.
-
Page 17: Pingmac
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands If the network transmits data rather slowly, you can set a bigger timeout. Related commands: tracert. Examples # Check whether the host with an IP address of 202.38.160.244 is reachable. -
Page 18: Tracert
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Note: At present, the pingmac command only supports detection of hosts in the same VLAN. Before executing the pingmac command, enable ndp in system view and port view first. - Page 19 Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands string: IP address of the destination host or host name of the remote system. Description Use the tracert command to trace the gateways involved in delivering a packet from source to destination.
-
Page 20: Tracemac Enable
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands 5 ccn-nerif22.Berkeley.EDU (128.32.168.22) 20 ms 39 ms 39 ms 6 128.32.197.4 (128.32.197.4) 59 ms 119 ms 39 ms 7 131.119.2.5 (131.119.2.5) 59 ms 59 ms 39 ms 8 129.140.70.13 (129.140.70.13) 80 ms 79 ms 99 ms... -
Page 21: Tracemac
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Examples # Enable the TraceMac and Ping Mac functions of the system. <H3C> system-view System View: return to User View with Ctrl+Z. -
Page 22: Command Line Parser Cache Function Commands
Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands 1.5 Command Line Parser Cache Function Commands 1.5.1 parser cache Syntax parser cache undo parser cache View System view Parameters None... - Page 23 Command Manual – System Maintenance and Debugging Chapter 1 System Maintenance and H3C S9500 Series Routing Switches Debugging Commands Description Use the display parser statistic command to query the state (enabled or disabled) of the parser cache function and statistics information.