Breaking In The Machine; Starting The Engine; Shutting Off The Engine - Toro Greensmaster 04358 Operator's Manual

•
Watch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles.
•
Choose a low ground speed so you will not have
to stop or shift while on a slope.
•
A rollover can occur before the tires lose traction.
•
Avoid operating the machine on wet grass. Tires
may lose traction; regardless if the brakes are
available and functioning.
•
Avoid starting, stopping, or turning the machine
on a slope.
•
Keep all movement on slopes slow and gradual.
Do not suddenly change the speed or direction of
the machine.
•
Do not operate the machine near dropoffs, ditches,
embankments, or bodies of water. The machine
could suddenly roll over if a wheel goes over the
edge or the edge caves in. Establish a safety area
between the machine and any hazard (2 machine
widths).

Breaking in the Machine

Refer to the engine manual supplied with the
machine for oil change and maintenance procedures
recommended during the break-in period.
Only 8 hours of mowing operation is required for the
break-in period.
Since the first hours of operation are critical to future
dependability of the machine, monitor its functions and
performance closely so that minor difficulties, which
could lead to major problems, are noted and can be
corrected. Inspect the machine frequently during
break-in for signs of oil leakage, loose fasteners, or
any other malfunction.

Starting the Engine

Note:
Inspect the area beneath the mowers to be
certain they are clear of debris.
1. Sit on the seat, ensure that the parking brake
is engaged, disengage the raise/lower mow
control, and move the functional control lever to
the N position.
EUTRAL
2. Ensure that your foot is not on the traction pedal
and make sure the pedal is in the N
position.
3. Move the choke lever to the O
when starting a cold engine) and the throttle
lever to the H
ALF
4. Start the engine and regulate the choke to keep
it running smoothly.
5. As soon as possible, open the choke by pulling
it rearward to the O
EUTRAL
position (only
N
T position.
HROTTLE
position.
FF
Note:
A warm engine requires little or no
choking.
6. Check the machine out with the following
procedures after the engine has started:
A. Move the throttle lever to the F
B. Move the traction-control lever to the M
position and momentarily engage the reels
by moving the raise/lower mow-control lever
forward.
The cutting units should drop and all the
reels should rotate.
C. Move the raise/lower mow control lever
rearward until the cutting units raise to the
full transport position.
The cutting units stop rotating as soon as
they start to lift. If you release the lever
before the cutting units are fully raised, the
upward motion stops, but the cutting units
still stop rotating.
D. Lock the parking brake and shut off the
engine.
E. Check the lip of each basket to ensure it is
not in contact with the reel during operation.
If you see signs of contact, adjust the pull
arms; refer to
(page 12).
F. Check for oil leaks and tighten the hydraulic
fittings if any are found.
Note:
When the machine is new and the
bearings and reels are tight, it is necessary
to use the F
this check. A fast throttle setting may not be
required after the break-in period.
Note:
If oil leaks continue to appear,
contact your authorized Toro distributor for
assistance and, if necessary, replacement
parts.
Important:
or wheel seals is normal. Seals require
a small amount of lubrication to perform
properly.

Shutting Off the Engine

1. Move the throttle lever to the S
disengage the raise/lower mow control, and
move the functional-control lever to the N
position.
2. Rotate the ignition key to the O
shut off the engine. Remove the key from the
switch to prevent accidental starting.
3. Close the fuel shut-off valve before storing the
machine.
21
AST
4 Installing the Cutting Units
throttle lever position for
AST
A trace of oil on the motor
position,
LOW
position to
FF
position.
OW
EUTRAL