Advertisement
Available languages
Available languages
INSTRUCTION
MANUAL
FOR
CHROMOFLEX PRO
SERIES
Remote Control 3-/4-Channel
PLEASE READ THIS MANUAL CAREFULLY
AND KEEP IT IN A SAVE PLACE!
2. USAGE
Colours and effects of the CHROMOFLEX
Pro can be controlled by remote control.
Settings being made can be stored on the
CHROMOFLEX Pro. After reconnecting the
supply voltage, the desired colour or effect
is set as start program. For operation the
remote control is equipped with solid-sta-
te touch keys / slider.
CHROMOFLEX Pro series operates on a
frequency of 868.3 MHz (licence-free in EU,
Switzerland, Norway and Iceland).
5. OPERATION
Please operate this unit only when it is
working properly.
In case of an error, switch off the unit
immediately. Do not operate the unit,
until the unit was verified electronically
by a qualified electrician.
A case of error is:
• Visible signs of damage on the unit
• The unit is not operating properly
• fume rising or crackling sounds from
the unit
• Visible signs of overheating
Item no. 66000025 and 66000045
remote control
for use with CHROMOFLEX Pro | Pro File
units 66000033; 66000034; 66000043;
66000044; 66000083; 66000084; 66000343;
66000344; 66000347; 66000348
1. INTRODUCTION
CHROMOFLEX Pro is an advancement of
CHROMOFLEX I, II and RC. The PRO version
consists of up to 4 channels (for modern
R-G-B-W LEDs) and is totally radio cont-
rolled.
For control and settings either one of
the CHROMOFLEX Pro devices (e.g. Art.
66000025) or CHROMOFLEX Pro USB
dongle (for PC/Art. 66000036) are re-
quired.
CHROMOFLEX Pro was designed so that
sophisticated illuminations in the field of
decoration and wellness can be attained
3. TECHNICAL DATA
Operating voltage: 3V DC
Batteries: 1 * 3V button cell CR2032
Protection class: III
Measures (L | W | H): 104 | 67 | 28mm
Ambient temperature: 0°C - max. +50°C
(in dry conditions only, non-condensing)
Radio frequency: 868.3MHz (licence-free
in EC, Switzerland, Norway and Iceland).
Manufacturer:
Josef Barthelme GmbH & Co. KG
5.1 START-UP
Please insert 3V button cell into the re-
mote control. Loosen, the screws on the
back of the remote control. Please insert
the batteries with correct polarity, because
otherwise the remote control may be da-
maged. Close housing again. The red LED
on the right side will flicker every 5 se-
conds for about 15 minutes. After about 15
minutes, the remote control automatically
switches to power saving mode, which can
be ended by pressing any key. To program
the remote control using the „ProCEd"
software, the unit must be in normal mode,
not in power saving mode.
even without programming. The unit is
equipped with various colour effects by
default such as: colours, calming colour
changes, even show effects. Some of them
can be edited or set as standard effect by
radio control.
Several CHROMOFLEX Pro can be linked
in a network, whereas all colour chan-
ges/scenes (except. random effects) are
in sync within the network automatically.
Therefore sophisticated illuminations can
be attained with a minimum of effort. Ope-
rating range depends on room conditions.
Operation of up to 300 metres should be
possible outdoors. Indoors an operating
range of 20-50 metres should be unpro-
blematic.
4. SAFETY INSTRUCTIONS
The unit is equipped with a built-in protec-
tion against reverse polarity. Connecting
the power in reverse polarity can destroy
the module, even if connected for a short
time only.
Please remove and replace empty batte-
ries because they could leak.
Barthelme declines any liability, loss or
damage caused by improperly used mo-
dules! Guarantee is also void in such cases.
This product is not a toy, keep away from
children!
FIG.: 1
Advertisement
