Table of Contents
Advertisement
.+.6
CE\ERAL
PROGRAM COMMENTS
?:-.g:":t. tJrld to
be as orisjnal as tltcir
- ;.:-'is.
t:o§Èter. a tè§, conventions.
rvhich
:
r
:
:
-.
r
sr:toorh soiution. should be followecl.
:
:IOP
,-ontnrand
must
be
provided Íbr
each
.....:l:
rhrt
ntust be jndexed. except for the
:-.'
:ir:t
is
indexed
prior
to
the start
of
the
:.
'g:.ill1.
-{
STOP command is mandatory at
.i,:
^9
11611,
80)
and step
l5g (row
g0
of
::-r:rd
!-ard) and step 237
(row g0 of
third
.
-:
j,
.,i
ntr.lli-card
programs.
l:
is recomntended that no lines be skipped
.,.
r::tin
a program, since the program
will
stop
.:.
blaitk step and CONTINUE must
be
:
-.!r'-.'d.
Also,
use
ol
unassigned
code numbers
::'i)
i.ruse incorrect results,
so
CLEAR
ALL
::-.ir
be pushed and the program
re_started-
\ÍLrlti-card programs
(2 or
more
cards)
::quire.
as
mentioned
above,
STOp comntands
,i
srep 80 (and
step
160 and step
240.
etc.).
\\:re1t the end
ol
the lirst
card
is
reachecl,
rt
is
r!-ntoved,
the next card is
inserted.
ancl
*ithout
clearing anything,
START
is pushed.
This procedure
is
repeated
for
any subsequent
;lrds.
The Model
CP-1
Card programmer also
has
STEP-AUTO switch locatecl on the side panel.
\\'hen the switch is on AUTO, the
program
steps
are
read
automatically in
sequence. When
the switch is on
STEP,
only
one
step
at
a
time is read. START must
be pushed
lbr
the
llrst
step and CONTINUE
for
each
step there-
after. The
STEP
mode is particularly
useful
rvhcn de-bugging, progrr
rn.
When
the
programmed automatic routine
is
started,
it
should be
allowecl
to
run
its
course.
If
the program must
be stoppcd, the
best procedure is
to
open
up
the Card
pro-
grammer. The
CLEAR
ALL
key should
not
be depressed
to
stop
a
program when
a
simul_
taneous electronic package
is
uscd.
If
this
condition should accidently occur, the
elcc_
tronic
paekage
may reqrrire rcpriming.
4.7
PROGRAM LIBRARIES
Program libraries are furnishecl
with
each
Section
4
program Operation
Model
CP-l
Card Programmer and range from
statistical applications
to
surveying applica-
tions. The libraries contain actual working pro-
grams
that
have been
developed
to
assist users
with
their requirements.
4.8
PROGRAM SETUP PROCEDURE
The setup procedure consists
of merely
con_
necting the Model
CP-l
Card programmer be-
tween the keyboard and the electrotric
pack_
age. Refer
to
the installation instructions in
Srction
2
for dt.tailed inslruclions.
CAUTION:
Ascertain
that
keyboard
pow_
er
is
off
before interconnecttns
equipment.
4.9
STARTING AND RUNNING THE
PROGRAM
This
procedure consists
of
inserting the pro-
gram card, starting
tlie
program, and keying-in
the data
as
required throughout the
course
of
the program. The following procedural
steps
are basic
to all
programs.
a.
Insert program card into Card program-
mer. Card is inserted
with
printed
side facing
the
pin
contacts and cropped corner
to
the
up-
per
right hand corner
of
the Card programmer.
Close Card Programmer
by
depressing thumb
Iocks-
b.
Turn on
keyboard
if
"ofl'
and
depress
CLEAR
ALL
key.
c.
Pen:se
program
work
sheet
for
specilic
instructior.rs.
d.
Ascertain
that
AUTO-STEp switch
on
Card Programmer
is
in AUTO
position_
NOTE:
Step position
of
AUTO-STEP
switch is
used
to
sequentially
check cach step
ol
a program,
The
CONTINUE switch
is
Lrscd
to
advance
the
program
stcp-
by+tep fbr
this operation m«le.
4*7
Advertisement
Table of Contents
