Related Manuals for Will Burt AntennaMast AM2 with EZ RAZE
Summary of Contents for Will Burt AntennaMast AM2 with EZ RAZE
- Page 1 Model AM2 with EZ RAZE ® Payload Elevation System Operator’s Manual www.antennamast.com...
- Page 2 *Page 6 explains the installation of the mast and accessories. **Page 7 lists the mast contents. Document History Version Date Remarks TP-5000901-00 04/03/14 Original Release Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
-
Page 3: Table Of Contents
..........18-19 Disassembling & Maintaining the Mast ......20 Customer Support Warranty Information ............21 Model # _____________ Serial # _____________ Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 4: Safety Precautions
Helmets or hard hats, eye protection, gloves, and safety shoes or combat boots must be worn while working in the mast deployment area. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 5: Operating Safety Precautions
Be certain electrical cables are undamaged and properly terminated. Always disconnect power before performing service, repair or test operations. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 6: Payload Capacity & Wind Effects
Stage & Stake guy lines • Load Tubes • Install Base Tube • Stake the Base Plate • Tighten the guy lines Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 7: Mast Contents
EZ RAZE Winch Mast Tube Lift Winch Kit Orange Lift Plate Orange Winch w/Key (Some models) Payload Accessory Kit As ordered Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... - Page 8 Manual Deployment www.antennamast.com...
-
Page 9: Installating The Tripod
Step on the base plates and lift the tripod up until the legs are fully extended. Lock each clamp by turning the knob to the right until tight. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... - Page 10 Be careful of buried cables and utilities when staking the mast. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
-
Page 11: Deploying The Mast
Then, slide the EZ RAZE carriage over the top of the tube section until resting on the top of the tripod. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 12: Deploying The Ez Raze System
To install the lift winch, insert the round key of the blue winch into the tripod receiver below the blue hold down clamp. Tripod Receiver Hold Down Clamp Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... - Page 13 Make sure the cable passes back down through the backside (180°) to single eyelet. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
- Page 14 Correct installation of cable end to the receiver plate. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
- Page 15 The manual lifter can also be used to push the tubes up. Repeat this step until all tubes are loaded. Tighten tripod clamp to maintain azimuth direction. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
- Page 16 For masts taller than 12m / 40 ft., two stakes are required, depending on the soil type. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
-
Page 17: Installing The Accessories
Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 18: Guying The Mast
Clip the carabineer of each of the tensioners to the ring of the guy stake. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... - Page 19 To adjust the guy line, move the ground stake related to the guy line by a couple of degrees. Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
-
Page 20: Disassembling & Maintaining The Mast
Inspect all guy lines for frayed or cut lines. Inspect guy handles for cracks or tears. Wipe down all parts with a cloth Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com... -
Page 21: Customer Support Warranty Information
169 S. Main Street Orrville, OH 44667 USA Corporate Telepone: +1-330-682-7015 Customer Service: +1-330-684-4000 Service & Parts: +1-330-684-5244 Fax: +1-330-684-1190 E-Mail: contact_us@willburt.com Do not duplicate, alter, or copy without the written consent of The Will-Burt Company. © Copyright 2013 The Will-Burt Company www.antennamast.com...
Need help?
Do you have a question about the AntennaMast AM2 with EZ RAZE and is the answer not in the manual?
Questions and answers