Advertisement
Quick Links
Advertisement
Related Manuals for Engl Cabloader
Summary of Contents for Engl Cabloader
- Page 1 CABLOADER Operator´s Manual...
- Page 2 As complicated as the digital wizardry is, that’s going on inside this little box. The CABLOADER has been designed with sheer simplicity and ease of use in mind. Even a complete new-comer to the world of digital cab sims and IR loaders can quickly set up an amazing sound with it’s intuitive controls.
-
Page 3: Pedal Layout
Save and recall your settings as a preset. Press and hold the footswitch for three seconds to save your current settings. Press to toggle your saved preset on/off. Simultaneously press and hold FAVOURITE A + FAVOURITE B for three seconds to bypass CABLOADER 10. CLIP LED CLIP LED indicates power on/off, input clipping and bypass mode. - Page 4 PEDAL LAYOUT 13. PHONES Dedicated headphone output 14. GROUND LIFT Use to eliminate ground loop noise when connected to the XLR OUTPUT 15. XLR OUTPUT Connect to this output using a balanced XLR cable 16. UNBALANCED OUTPUT Connect to this output using a standard 1/4” jack cable 17.
- Page 5 Here are a couple of our recommended setups. PEDALBOARD In this setup CABLOADER is being used to transform your regular gain pedals into a full sounding amp rig for connecting directly to the PA and/or audio interface device. AUDIO INTERFACE...
- Page 6 AMPLIFIER to the PA system and/or audio interface with full speaker cab simulation for a great path, so your amp can still be heard through it’s real life speaker cabinet for on-stage monitoring. AUDIO INTERFACE HEADPHONES PA MIXER AMP + CAB Always ensure that there is a speaker cabinet or a load of the correct impedance speaker output.
- Page 7 FAVOURITES CABLOADER lets you store and recall 2 of your favourite cab setups as presets using the FAVOURITE A and FAVOURITE B footswitches. This allows you to easily toggle bet- ween either of your “favourite” setups and also the current settings of the pedal’s control knobs.
-
Page 8: Bypass Mode
This effectively lets you switch between 3 completely different cab setups with ease. BYPASS MODE Press and hold for 3 seconds Press and hold both footswitches for 3 seconds to BYPASS the CABLOADER pedal. All LED’s will turn off to indicate BYPASS mode. Press any footswitch to exit BYPASS MODE. -
Page 9: Cab Models
Engl E412 Standard Celestion V60* 4 x 12 Engl E412 Pro Celestion Vintage 30* 4 x 12 Engl E412 Pro XXL Celestion Vintage 30* 4 x 12 Engl E412 Pro Celestion Greenback G12M-25* 4 x 12 Engl E412 Pro Celestion Creamback G12M-65*... - Page 10 MIC MODELS MIC MODEL MODEL BASED ON Shure SM 57 Dynamic* Shure SM 58 Dynamic* Sennheiser MD 421 Dynamic* Sennheiser MD 441U Dynamic* 2001P Marshall MXL 2001P* 2003 Marshall MXL 2003* Rode NT-1* 4000B AKG C4000B* Neumann U87* Neumann U47* Please Note: *The manufacturers and product names mentioned above are trade- marks or registered trademarks of their respective owners.
-
Page 11: Specification
IR LOADING SPECIFICATION Output: 1 x 1/4“ Unbalanced, 1 x XLR, 1 x THRU, 1 x Headphone USB Port: Micro-B Sampling rate: at least 44.1KHz Sampling accuracy: 24bit Signal to noise ratio: 100dB IR Format: .wav Sampling Length: 1024 Samples (23.22ms) Power Requirements: 9V DC 300mA Dimensions: 120mm(D) x 95mm(W) x55.5mm(H) Weight: 409g... - Page 12 www.engl-amps.com...