Table of Contents
Advertisement
Quick Links
Germany | Switzerland | Austria
Benelux
Althen GmbH Mess- & Sensortechnik
Althen bv Sensors & Controls
Tel: + 49 (0)6195 - 70060
Tel: +31 (0)70 392 4421
info@althen.de
sales@altheris.nl
Single Axis
Tilt Measuring System
France
Althen / DB Innovation
Tél : 0033 (0)4 67 78 61 66
info@althensensors.fr
Sweden
USA | Canada
Althen Sensors & Control AB
Altheris Inc Sensors & Controls Inc.
Tel. +46 (0)8 7 95 24 90
Tel: +1 858-633-3572
info@althensensors.de
info@althensensors.com
Other Countries
please contact us
by email at
sales@althensensors.com
www.althen.de
V2.1 eng
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ALTHEN NM1-IP-2L-420-B05
Summary of Contents for ALTHEN NM1-IP-2L-420-B05
- Page 1 Germany | Switzerland | Austria Benelux France Sweden USA | Canada Other Countries Althen GmbH Mess- & Sensortechnik Althen bv Sensors & Controls Althen / DB Innovation Althen Sensors & Control AB Altheris Inc Sensors & Controls Inc. please contact us...
-
Page 2: Table Of Contents
Content 1 General Information ........................... 3 1.1 Safety Instructions ........................3 1.2 Qualified Personnel ........................3 1.3 Intended Use ..........................3 2 Instructions for use of the measuring amplifier ..............4 3 Technical Description ........................5 4 Terminal Assignment........................5 4.1 Supply Voltage .......................... -
Page 3: General Information
To ensure reliable and safe operation, the measuring amplifier must be operated in compliance with the specifications according to this technical description only. These regulations must also be observed if accessories, which have been ordered from Althen Mess- & Sensortechnik GmbH together with the measuring amplifier, are being used. -
Page 4: Instructions For Use Of The Measuring Amplifier
Notice: Changes of the measuring system of any kind demand for the explicit approval of Althen Mess- & Sensortechnik GmbH. Changes of any kind done without that approval exclude all possible warranty and/or liability of Althen Mess- & Sensortechnik GmbH. -
Page 5: Technical Description
3 Technical Description This single axis, industrial tilt measuring system, which consists of one none-contact sensor and an electronic customized for said sensor, serves to measure accurate tilt angles in x-axis and it is intended for side wall mounting. Depending on the version the tilt angle can be between ± 3 up to ± 60°, or between 0 …... -
Page 6: Starting Up
Before mounting, all transport protection has to be removed and disposed of properly. The measuring object is to be leveled horizontally (e.g. using the PRO3600 protractor from ALTHEN). The sensor is to be mounted to a vertical surface at the object to measure. -
Page 7: Calibration Of The Tilt Measuring System
5.1 Calibration of the tilt measuring system Notice: The measuring system is factory pre-calibrated. Under normal circumstances, an adjustment is not necessary. After mounting the system, caused by deviations of mounting, a slight correction of the zero-point is often necessary. The calibration of the span / full-scale is to be checked. 5.1.1 Adjusting the zero-point - Connect an amperemeter ■... -
Page 8: Maintenance
Amplifiers and measurement units manufactured and sold by Althen Mess- & Sensortechnik GmbH serve B2B purposes only. Therefore, those old appliances must not be given to the communal disposer, but must be given back to the seller or disposed of properly. -
Page 9: Appendix
Appendix Datasheet Number of measuring axis: Supply voltage: 18…28 VDC Protected against voltage reversal Power consumption: ca. 3 W Analogue output 4 … 20 mA (2-wire) Max. impedance depending on voltage Frequency (-3dB): 0,5 Hz ±3°, ±5°, ±10°, ±15, ± 20, ±30, ±45° Preferred measuring ranges Other ranges on request 0…10°, 0…30°, 0…45°, 0…60°, 0…90°... -
Page 10: Housing Dimensions
Housing Dimensions 10 | 12... -
Page 11: Emc-Mounting
EMC-Mounting Enclosure with high- frequency-seal Keep enclosure closed EMI-/RFI-approved To improve the noise- cable lead-through Use with cable Connect screen to immunity feed the leads connect to screen screen ground with through ferrite-rings ground-clamp Amplifier/Sensor Grounding case: Case need to be mounted on a grounded surface! Step... - Page 12 Subject to modifications. All information describe our products in general form. 12 | 12...
Need help?
Do you have a question about the NM1-IP-2L-420-B05 and is the answer not in the manual?
Questions and answers