Table of Contents
Advertisement
Quick Links
Operating and mounting manual
EVF
Contents
1.1
1.2
2.1
2.2
2.3
2.4
2.5
2.6
3.1
3.2
3.3
4.1
4.2
4.3
5.1
5.2
Installation
6.1
6.2
6.3
6.4
7.1
7.2
8.1
10.0
11.0
11.1
Sectional drawing
11.2
11.3
12.0
_______________________________________________________________________________________________________
220.100.112-07
TM 3926
Operating and mounting manual
Safety shut off valve
gas - solenoid valve
Page 1 /13
(translation)
EVF
Version: 12/2015
Advertisement
Table of Contents
Troubleshooting
Related Manuals for UNI Geräte EVF Series
Summary of Contents for UNI Geräte EVF Series
-
Page 1: Table Of Contents
Operating and mounting manual (translation) Operating and mounting manual Safety shut off valve gas – solenoid valve Contents 1.0 General Remarks Valve data Application 2.0 Danger Notices Safety terms Safety notice Qualified staff Unauthorized modification and spare part production Unauthorized operation Safety information for the use in explosion-prone areas guideline 94/9/EC 3.0 Handling Transport... -
Page 2: General Remarks
Operating and mounting manual (translation) 1.0 General Remarks This operating manual includes instructions to assemble and operate the valve in the prescribed and safe way. Additionally, the adeqaute operating instructions (BTA) of each special solenoid drive must be considered. Series MG... 220.100.038 Series MG...X 220.100.040... -
Page 3: Application
Operating and mounting manual (translation) Voltage: VDC 12 – 440 (–15% to +10%) VAC 24 – 500 (–15% to +10%) Protection type: IP54 or IP65 Frequency: 40 – 60 Hz Power: 10 – 4000W Details to the electrical data can be found on the type signand the adeqaute operating instructions of the solenoid valves. -
Page 4: Unauthorized Modification And Spare Part Production
Operating and mounting manual (translation) Instruction and obligation to carry out and meet all regional and in-house orders and requirements. Education or instruction according to the safety engineering standards in use and maintenance of adequate safety and working protection equipment. ... -
Page 5: Storage
Operating and mounting manual (translation) Storage If the valve is not installed immediately after delivery, it must be stored properly. Storage temperature -20°C up to +60°C, dry and clean. The lacquering protects against corrosion in neutral dry atmosphere. Do not damage colour. ... -
Page 6: Marking
Operating and mounting manual (translation) Marking The type sign on the solenoid drive has the following information: Fabricator Valve type, nominal width, pressure and temperature indication, fitting position Year of construction/ production no. Product ID No. ... -
Page 7: Commissioning
Operating and mounting manual (translation) DANGER! Before commissioning a new installation or before starting up an installation again after repairs or modifications, ensure: The proper completion of all installation and assembly work! Commissioning only by “qualified staff” (see point 2.3). ... -
Page 8: Troubleshooting Plan
Operating and mounting manual (translation) Troubleshooting plan Malfunction Possible causes Remedy No flow Valve does not open Switch on solenoid drive (800) Check operating voltage Working pressure too high Compare working pressure with the data on the rating plate Flange covers were not removed Remove flange covers Low flow rate Clogging in the pipework system... -
Page 9: Warranty
Operating and mounting manual (translation) 9.0 Warranty Scope and period of the warranty is specified in the edition of the “General Terms of Business of the UNI-Geräte E. Mangelmann Elektrotechnische Fabrik GmbH” valid at the time of delivery or else in the purchase agreement. -
Page 10: Drawing
Operating and mounting manual (translation) 11.0 Drawing 11.1 Fig.1 40-EVF…NH.Ü.. (DN15 – DN25) ; 55-EVF…NH.Ü.. (DN15, DN25) 901/3 901/4 901/3 901/2 219/2 943/2 219/1 503/2 901/1 902/2 941/2 943/1 941/1 503/1 910/2 948/2 402/3 910/1 948/1 402/2 402/1 902/1 116.001.755 Spare parts _______________________________________________________________________________________________________ 220.100.112-07... -
Page 11: View Drawing
Operating and mounting manual (translation) 11.2 View drawing 40-EVF…NH.Ü.. (DN15 – DN25) ; 55-EVF…NH.Ü.. (DN15, DN25) 11.3 List of parts Pos./ Item Stück/ Qty. Benennung Description Endschalteranbau Limit switch mounting Ventilgehäuse Valve chamber Gehäuseoberteil Upper part of housing Gehäuseflansch Housing flange Gehäusezylinder Housing cylinder... - Page 12 Operating and mounting manual (translation) Pos./ Item Stück/ Qty. Benennung Description Faltenbalg Expansion bellows Distanzring Distance ring Endschalterbetätigung Switch actuator Klemmkasten Terminal box Magnet-Antrieb Solenoid drive Endschalter Limit switch 901/1 Sechskantmutter Hex. nut 901/2 Sechskantmutter Hex. nut 901/3 Sechskantmutter Hex. nut 901/4 Sechskantmutter Hex.
-
Page 13: Declaration Of Conformity
Operating and mounting manual (translation) 12.0 Declaration of Conformity _______________________________________________________________________________________________________ 220.100.112-07 Page 13 /13 Version: 12/2015 TM 3926...