Related Manuals for Metreel ALULIFT
Summary of Contents for Metreel ALULIFT
- Page 1 ALULIFT ® Portable Aluminum Gantry Crane Operation & Maintenance Instructions Tel: 877 830-9803 Fax: 713 541-0530 Email: sales@metreel.com Website: www.metreel.com...
-
Page 2: Table Of Contents
Portable Aluminum Gantry Crane Operation & Maintenance Instructions CONTENTS Caution ................................3 Pre-Build Check List............................4 Initial Set Up ..............................5-6 Assembly Instructions ............................ 6-8 Adjusting the Height............................9 Moving The Gantry Under Load ......................... 10 Maintenance Instructions ..........................10 Parts List ................................. 11 Warranty ................................. -
Page 3: Caution
Portable Aluminum Gantry Crane Operation & Maintenance Instructions IMPORTANT Before assembly or operation of this gantry, please read these instructions carefully. • ENSURE no parts are missing or damaged. A full list of required parts can be found on Page 10 of this manual and a Pre-Build Check List is on Page 4 •... -
Page 4: Pre-Build Check List
Portable Aluminum Gantry Crane Operation & Maintenance Instructions PRE-BUILD CHECK LIST 1 x Beam 2 x Upright Assemblies 2 x Leg Kits 6 x Loop Pins 4 x Wheel Assemblies 1 x Hoist Trolley Document No. TD005-0618 Last Updated: 21 June 2018 Page 4 of 12... -
Page 5: Initial Set Up
Portable Aluminum Gantry Crane Operation & Maintenance Instructions INITIAL SET UP (Should only have to be done once) Building The A-Frame’s Step 01 Place the Upright Assembly on the floor as shown in Fig 01 Align the angled length to the bottom pre-drilled hole of the top plate as shown in Fig 02 Bolt together using the supplied fixings as shown in Fig 03 Fig 01 Fig 02... -
Page 6: Assembly Instructions
Portable Aluminum Gantry Crane Operation & Maintenance Instructions ASSEMBLY INSTRUCTIONS Before assembling the gantry, please ensure that there is no machinery or equipment which could impede the assembly operation. ALL personnel should wear appropriate safety gear, such as hard hats, safety shoes and gloves. - Page 7 Portable Aluminum Gantry Crane Operation & Maintenance Instructions Step 04 Engage the brakes on both castors at the end opposite to the first lift as shown in Fig 10. This is to ensure the A-Frame will not move when raising the beam. Fig 10 Step 05 With one person holding the beam, another person should raise the A-Frame slowly by wheeling the legs into the...
- Page 8 Portable Aluminum Gantry Crane Operation & Maintenance Instructions Step 06 Release brakes on castors, Fig 13 and raise the other A-Frame similarly with one person holding the main beam, whilst another person raises the A-Frame slowly by wheeling the legs into the upright position. to the beam, use the locking pin, shown in Fig 14 to secure the A-Frame in it’s vertical position.
-
Page 9: Adjusting The Height
Portable Aluminum Gantry Crane Operation & Maintenance Instructions ADJUSTING THE HEIGHT First secure the trolley and hoist to one of the Gantry A-Frames, preventing movement along the Beam. We advise that you should only raise/lower one end at a time and that you do not raise/lower more than 2 height increments in any one movement. -
Page 10: Moving The Gantry Under Load
Portable Aluminum Gantry Crane Operation & Maintenance Instructions MOVING THE GANTRY UNDER LOAD Under certain circumstances it is possible to use the gantry to transport the load. This should ONLY be carried out if the ground towards the destination is level, sound surface and two or more people are present. We would also advise that you follow this procedure when moving the gantry. -
Page 11: Parts List
Portable Aluminum Gantry Crane Operation & Maintenance Instructions PARTS LIST & DRAWING Parts List Lifting Beam Safe Working Load Plates Top Plate Upright Assembly Leg Kit Loop Pins Hoist Trolley Wheels (braked) Document No. TD005-0618 Last Updated: 21 June 2018 Page 11 of 12... -
Page 12: Warranty
Metreel Inc.’s written authorization. Written notice of any claimed system defect must be given to Metreel Inc.’s within thirty days of discovery. Metreel Inc.’s obligation under this warranty is limited to the replacement or repair of Metreel Inc.’s products at the factory or separate location approved by Metreel Inc.
Need help?
Do you have a question about the ALULIFT and is the answer not in the manual?
Questions and answers